background image

44

WARRANTY

1

Soundcraft is a trading division of Harman International Industries Ltd .
End User means the person who first puts the equipment into regular operation.
Dealer means the person other than Soundcraft (if any) from whom the End User purchased the
Equipment, provided such a person is authorised for this purpose by Soundcraft or its accredited
Distributor.
Equipment means the equipment supplied with this manual.

2

If within the period of twelve months from the date of delivery of the Equipment to the End User it
shall prove defective by reason only of faulty materials and/or workmanship to such an extent that
the effectiveness and/or usability thereof is materially affected the Equipment or the defective
component should be returned to the Dealer or to Soundcraft and subject to the following condi-
tions the Dealer or Soundcraft will repair or replace the defective components. Any components
replaced will become the property of Soundcraft.

3

Any Equipment or component returned will be at the risk of the End User whilst in transit (both to
and from the Dealer or Soundcraft) and postage must be prepaid.

4

This warranty shall only be valid if:
a)

the Equipment has been properly installed in accordance with instructions contained in

Soundcraft’s manual; and
b)

the End User has notified Soundcraft or the Dealer within 14 days of the defect appearing;

and
c)

no persons other than authorised representatives of Soundcraft or the Dealer have effected

any replacement of parts maintenance adjustments or repairs to the Equipment; and
d)

the End User has used the Equipment only for such purposes as Soundcraft recommends,

with only such operating supplies as meet Soundcraft’s specifications and otherwise in all respects
in accordance with Soundcraft’s recommendations.

5

Defects arising as a result of the following are not covered by this Warranty: faulty or negligent
handling, chemical or electro-chemical or electrical influences, accidental damage, Acts of God,
neglect, deficiency in electrical power, air-conditioning or humidity control.

6

The benefit of this Warranty may not be assigned by the End User.

7

End Users who are consumers should note their rights under this Warranty are in addition to and do
not affect any other rights to which they may be entitled against the seller of the Equipment.

Summary of Contents for EFX12













































Reviews: