background image

21

7  2 TRACK IN

These two RCA phono sockets are unbalanced Left and Right line-level inputs, used for connecting a play-
back device.

8 2 TRACK TO MIX

Press this switch to route the 2 Track  in signals, connected to the Left and Right RCA sockets 7, to the MIX
Left/Right signal at the MIX outputs.

9 MONITOR 2 TRACK

Press this switch to route the 2 Track signal to the monitor and phones, over-riding the default Monitor/
Phones signal.

10 MONITOR LEVEL

This control sets the level to the MONITOR LEFT & RIGHT outputs.  If headphones are plugged into the
PHONES jack, the headphone level will track the Monitor Level.

11 MONITOR OUTPUTS

The Monitor Outputs are on 3-pole ‘A’ gauge jacks and are balanced connections

12 PHONES LEVEL

This control sets the output level to the Headphone outputs.  If headphones are plugged into the PHONES
jack, then the knob sets a comfortable headphone listening level without affecting the Monitor output levels.

13 HEADPHONES JACK

The PHONES output is a 3-pole ‘A’ gauge jack, wired as a stereo output as shown, ideally for headphones of
150

 or greater.  8

 headphones are not recommended.

14 AUX 1 OUTPUT

This output is on a 3-pole ‘A’ gauge jack and is a balanced output.

15 AUX 1  PRE/POST SWITCH

This switch globally switches the AUX 1 sends, on all of the input modules, to be either pre-fade or post-fade.

16 FX BUS OUTPUT

This output carries the signal from the FX bus. It could be used as a second Aux Output if desired, if the FX
Processor is not needed at the time. The FX sends on the inputs channels to the FX bus are always post-fade.

17 FOOTSWITCH

This is used by the FX Processor, see page 23.

18 STEREO RETURN INPUTS

This pair of inputs accept 3-pole ‘A’ gauge (TRS) jacks.  Use these inputs for sources such as keyboards, drum
machines, synths or CDs.  The inputs are BALANCED. Mono sources may be used by plugging into the left jack
only.

19 STEREO RETURN LEVEL

This control sets the level of signal routed to the main mix busses. There is an associated PK LED to warn of
signals which are too high.

Summary of Contents for EFX12













































Reviews: