Sound Skulptor EQ573 Assembly Manual Download

Page: 6 / 10

www.soundskulptor.com

Document revision 1.1 – Last modification : 01/05/14

EQ573 Assembly guide – IO board

23. Resistors

Add R1 to R16.
Control the resistor values with a digital multimeter. Bend the leads at 0.4” with a lead forming tool.

24. Ceramic capacitors

Add C1, C2, C7, C8, C10.

25. IC Sockets

Insert and solder the 8 pins sockets of UI and U2. Do not insert U1 at this time.

Warning

: Make sure to respect the socket direction, marked by a notch.

26. Electrolytic capacitors

Add C9, C11, C12, C15 to C18, C13, C14, C3 to C6.
Solder one lead first, adjust verticality then solder the second lead.

Warning

: The +lead must go into the +hole. Do not reverse (they may explode !)

27. Connector
Solder the connector CN4B. Solder one pin first, check verticality, then solder the other pins.

Warning

: the connector pins must be exactly perpendicular to the PCB to allow proper insertion into the

main board.

28. IC's

Insert U1 and U2 in their respective socket.

EQ573 Assembly guide – Final assembly

29. Front pannel assembly

Attach the 15mm female/female spacer to the front panel with
an M3x6 countersunk black screw.
Next, insert the switches into the front panel and attach the
switches board to the 15mm spacer with one M3x6 screw.

Summary of Contents for EQ573











Search results

Summary of Contents for EQ573

Reviews:

Related manuals for EQ573

Brands by name

Popular brands

Sound Skulptor EQ573, Assembly Manual

Search results

Summary of Contents for EQ573

Reviews:

Related manuals for EQ573

Brands by name

Popular brands