manualshive.com logo in svg

Sound Skulptor CP5176, Assembly Manual, Page: 7 / 12

Share
Download
Sound Skulptor CP5176 Assembly Manual Download Page 7

www.soundskulptor.com

Document revision 2.1 – Last modification : 12/11/17

CP5176 Assembly guide – Main PCB

25. Visual check

Brush the solder side with a hard tooth brush to remove any remaining solder bits.

Make a full visual check. Any missing component on the board ? Any remaining component in the box ?
When everything looks correct, proceed with the front PCB assembly.

CP5176 Assembly guide – front PCB assembly

26. Diode

Add D3. This diode is installed vertically.

Warning

 : Make sure to respect the direction of the diode which is marked by a ring on the component 

and letter K on the PCB marking.

1. Resistors

Add R28 to R32, R36 to 39.
Control the resistor values with a digital multimeter. The resistors are installed vertically.

2. Ceramic capacitor

Add C19.

3. Connectors 2x10

Solder the two 2x10 connectors on the back of the PCB, inserted from the solder side.

4. Spacers

Attach two 15 mm spacers with two M3x6 mm screws, inserted from the solder side.

Copyright ©2013 to Today SoundSkulptor

Summary of Contents for CP5176













Reviews:

No comments