background image

11

GB

0dB

D.BASS-3

D.BASS-2

D.BASS-1

D.BASS-3

D.BASS-2

D.BASS-1

Boosting the bass sound

— D-bass

You can enjoy a clear and powerful bass
sound. The D-bass function boosts the low
frequency signal and high frequency signal
with a sharper curve than conventional bass
boost.
You can hear the bass line more clearly even
while the vocal volume remains the same. You
can  emphasize and adjust the bass sound
easily with the D-BASS button.

Adjusting the bass curve

Press 

(D-BASS)

 repeatedly to select the

desired bass curve.

As the D-BASS number increases so does
the effect.

D.BASS-1 

t

 D.BASS-2 

t

 D.BASS-3 

t

D.BASS-OFF

Note
The bass sound may distort at same volume. If the
bass sound distorts, select less effective bass curve.

Level

Frequency (Hz)

Press 

(MBP)

 repeatedly until the desired

listening position.

Mode of “My Best sound Position” will be
shown in the display in order of the table.

After one second, the display goes back to
the normal playback mode.
If you want to adjust the sound level of
balance and fader more precisely, you can
do it in 

(SEL)

 button. (See “Adjusting the

sound characteristics” on page 10.)

Selecting the sound
position 

— “My Best sound Position”

When you drive without passengers, you can
enjoy comfortable sound environment by “My
Best sound Position.”
“My Best sound Position” has two presets,
which adjusts the sound level of balance and
fader. You can select one very easily with MBP
button.

Display

window

MBP-A

MBP-B

MBP-OFF

Right

– 4dB

0

0

Left

0

– 4dB

0

Front

0

0

0

Rear

– 4dB

– 4dB

0

Balance Level

Fader Level

Summary of Contents for XR-CA320







































Reviews: