29
MZ-R909
156. Adjust with the
[VOL+]
key (adjusted value up) or
[VOL--]
key (adjusted value down) so that the adjusted value becomes
F0.
157. Press the
X
key.
(1041 is blinking)
158. Press the
[VOL+]
key once to change the blinking portion to
1042.
159. Press the
x
key.
(00 is blinking)
160. Adjust with the
[VOL+]
key (adjusted value up) or
[VOL--]
key (adjusted value down) so that the adjusted value becomes
B0.
161. Press the
X
key.
(1042 is blinking)
162. Press the
[VOL+]
key once to change the blinking portion to
1043.
163. Press the
x
key.
(00 is blinking)
164. Adjust with the
[VOL+]
key (adjusted value up) or
[VOL--]
key (adjusted value down) so that the adjusted value becomes
E1.
165. Press the
X
key.
(1043 is blinking)
166. Press the
[VOL+]
key twice to change the blinking portion to
1045.
167. Press the
x
key.
(00 is blinking)
168. Adjust with the
[VOL+]
key (adjusted value up) or
[VOL--]
key (adjusted value down) so that the adjusted value becomes
B0.
169. Press the
X
key.
(1045 is blinking)
023
1041F0
Remote commander LCD display
F0
: Adjusted value
023
104200
Remote commander LCD display
00
: Adjusted value
023
1042B0
Remote commander LCD display
B0
: Adjusted value
170. Press the
[VOL+]
key twice to change the blinking portion to
1047.
171. Press the
x
key.
(00 is blinking)
172. Adjust with the
[VOL+]
key (adjusted value up) or
[VOL--]
key (adjusted value down) so that the adjusted value becomes
03.
173. Press the
X
key.
(1047 is blinking)
174. Press the
[DISPLAY]
key on the remote commander for sev-
eral seconds (about 3 seconds) to exit the patch data write
mode and display as below.
175. Press the
X
key to write the modified data.
176. The modified data writing is over, if the adjusted value
changes to DD.
177. Turn the power off.
• Modified data writing method (version 2.000)
1. Select the manual mode of the test mode, and set item number
022 (see page 13).
2. Press the
X
key to initialize the patch data.
(The modified data writing is over, if the adjusted value changes
to DD)
3. Press the
N
key or
>
key to set item number 023.
4. Press the
[VOL+]
key once to change the adjusted value to 01.
5. Press the
[DISPLAY]
key on the remote commander for sev-
eral seconds (about 3 seconds) to activate the patch data write
mode.
(The following display will appear where 00 is blinking)
023
104300
Remote commander LCD display
00
: Adjusted value
023
1043E1
Remote commander LCD display
E1
: Adjusted value
023
104500
Remote commander LCD display
00
: Adjusted value
023
1045B0
Remote commander LCD display
B0
: Adjusted value
023
104700
Remote commander LCD display
00
: Adjusted value
023
104703
Remote commander LCD display
03
: Adjusted value
023
Patch0A
Remote commander LCD display
0A
: Adjusted value
023
***SDD
Remote commander LCD display
DD
: Adjusted value
023
Patch00
Remote commander LCD display
00
: Adjusted value
022
PatClr CC
Remote commander LCD display
022
***SDD
Remote commander LCD display
DD
: Adjusted value
023
102800
Remote commander LCD display
00
: Adjusted value