background image

Projector Driver Application Note

Sony VPL-FE100U Series

Revision A

DR-SNY04 - 11/7/01

SP Controls reserves the right to modify specifications without notice at any time.

This document describes the 

SmartPanel

 Projector Driver for the 

Sony VPL-FE100U 

projector. For

general information on configuring and using the Panel, see the 

SmartPanel Configuration and Installation

Guide.

NOTE:  

The Sony projector must be specially configured during installation. For instructions on

configuration requirements, see the 

Special Control Note

 in 

Section III

 below.

I. PROJECTOR CONTROL

A.   Volume and Power Control

Volume control on the Sony is 

relative

.  However, on-screen display indicates the current volume level.

Absolute volume control is possible with use of SP Controls’ optional 

Audio Follow Video Pre-Amplifier

.

B.   Input Selection Mapping

The following table specifies the factory-preset input mapping for this Driver. The 

Configuration Utility

can be used to customize these settings your installation.

Selection 1:

VIDEO

Selection 2:

S-VIDEO

Selection 3:

INPUT A

Selection 4:

INPUT B

Input choices available for this Driver are VIDEO,
S-VIDEO, INPUT A, INPUT B, and INPUT C.

NOTE

: Input-type must be specified for Inputs A, B, and C for this projector.  See the 

Special Control

Note, Section III 

for more information.

NOTE

: INPUT B and INPUT C do not ship with the projector and must be custom-ordered.

C.  

Hidden Function Mapping

The following table specifies the factory preset hidden function mapping for this Driver. The

Configuration Utility

 can be used to customize these settings your installation.

Selection 1:

APA (AUTO IMAGE)

Selection 2:

ENTER

Selection 3:

ADJUST LEFT

Selection 4:

ADJUST RIGHT

Off:

MENU

Volume Up:

ADJUST UP

Volume Down:

ADJUST DOWN

Hidden functions are accessed by pressing the indicated key while the holding the 

On 

key down.  Hidden

functions names are based on the Sony remote and the controls on top of the projector.

Projector

Ready

Warm-up

OFF

OFF

OFF

OFF

ON

ON

ON

ON

Volume

VIDEO

S-VIDEO

INPUT A

INPUT B

Projector

Ready

Warm-up

OFF

OFF

OFF

OFF

ON

ON

ON

ON

Volume

ADJUST

 UP

ADJUST

 DOWN

MENU

ENTER

ADJUST

LEFT

ADJUST

 RIGHT

APA

Summary of Contents for VPL-FE100U







Reviews: