manualshive.com logo in svg

Sony TRINITRON KV-ES34M90, Service Manual

Share
Download
Sony TRINITRON KV-ES34M90 Service Manual Download Page 8

http://cxema.ru

– 8 –

KV-ES34M90

RM-916

SECTION  1

GENERAL

The operating instructions mentioned here are partial abstracts 

from the Operating Instruction Manual.  The page numbers of 

the Operating Instruction Manual remain as in the manual.

2

W

ARNING

•  Danger

ously high voltages ar

e pr

esent inside the TV

.

•  Operate the TV only between 1

10 – 240 V 

AC.

To prevent fire or shock hazard, do not expose

the TV to rain or moisture.

Do not operate the TV if any liquid or solid object

falls into it. Have it checked immediately by

qualified personnel only.

Do not open the cabinet and the rear cover of the

TV. Refer servicing to qualified personnel.

Do not install the TV in hot, humid or excessively

dusty places.

Do not install the TV in a confined space, such

as a bookcase or built-in cabinet.

Do not block the ventilation openings of the TV.

Install the TV in a stable position. Do not allow

children to climb onto it.

Do not plug in too many appliances to the same

power socket. Do not damage the power cord.

Clean the TV with a dry and soft cloth.

Do not use benzine, thinner, or any other chemicals

to clean the TV. Do not scratch the picture tube.

For your own safety, do not touch any part of the

TV, the power cord and the antenna cable during

lightning storms.

Pull the power cord out by the plug. Do not pull

the power cord itself. Disconnect the TV if you

are not going to use it for several days.

4

Using Y

our New TV

Getting Started

 Step 1

Connect the antenna

If you wish to connect a VCR, see the “Connecting a VCR” diagram below

.

CAUTION

Do not connect the power cor

d until all other connections ar

e complete;

otherwise, a minimal curr

ent leakage thr

ough the antenna and/or other

terminals to the gr

ound could occur

.

Connecting a VCR

T

o

 play a video tape, pr

ess 

t

 (see page 1

1).

Using Y

our New TV

: Signal flow

IEC connector

(not supplied)

or

Antenna cable (not supplied)

Antenna cable (not supplied)

Rear of TV

To

 video and

audio outputs

To

 S video

output

Audio/Video cable

(not supplied)

S video cable

(not supplied)

: Signal flow

To

 

(S video input)

VCR

Antenna cable (not supplied)

To

 antenna

output

To

 

˘

 (antenna)

R

L

2

3

Y

C

B

C

R

VIDEO

VIDEO IN

VIDEO OUT

AUDIO

R       L

R

L

(MONO)

DIGIT

AL IN

(DOLBY DIGIT

AL/PCM)

1

Rear of TV

To

 

t

 1, 2 or 3 (video input)

 (yellow)

-L (MONO) (white)

-R (r

ed)

Summary of Contents for TRINITRON KV-ES34M90









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands