![background image](http://html.mh-extra.com/html/sony/ss-spsd5/ss-spsd5_service-manual_1329662002.webp)
2
TABLE OF CONTENTS
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SA-PSD5/WPSD5/SS-SPSD5
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
SAFETY CHECK-OUT
To Exposed Metal
Parts on Set
0.15
µ
F
1.5 k
Ω
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY CHECK-OUT
················································· 2
1.
GENERAL
········································································· 3
2.
DIAGRAMS
······································································· 4
2-1. Circuit Boards Location ························································ 4
2-2. Block Diagrams ···································································· 5
2-3. Printed Wiring Board
– Digital Section (Side A) – ·················································· 6
2-4. Printed Wiring Board
– Digital Section (Side B) – ················································· 7
2-5. Schematic Diagram – Digital Section (1/2) – ······················· 8
2-6. Schematic Diagram – Digital Section (2/2) – ······················· 9
2-7. Schematic Diagram – LCD Section – ··································· 10
2-8. Printed Wiring Board – LCD Section – ································ 11
2-9. Schematic Diagram – Key Section – ···································· 12
2-10. Printed Wiring Board – Key Section – ·································· 13
2-11. Schematic Diagram – IN/OUT Section – ····························· 14
2-12. Printed Wiring Board – IN/OUT Section – ··························· 15
2-13. Schematic Diagram – Pre Amp Section – ····························· 16
2-14. Printed Wiring Board – Pre Amp Section – ·························· 17
2-15. Schematic Diagram – Power Section (1/2) – ························ 18
2-16. Schematic Diagram – Power Section (2/2) – ························ 19
2-17. Printed Wiring Board – Power Section – ······························ 20
2-18. IC Block Diagrams ······························································· 21
2-19. IC Pin Function Description ················································· 23
3.
EXPRODED VIEWS
······················································· 25
3-1. SA-WPSD5 (FRONT SECTION) ········································· 25
3-2. SA-WPSD5 (AMP SECTION) ············································· 26
3-3. SS-SPSD5 ············································································· 27
4.
ELECTRICAL PARTS LIST
········································ 28
Summary of Contents for SS-SPSD5
