background image

3

Powered Mixer Has 170W+170W(4

) Power Amplifier,

and 4 Microphones, 3 Line Inputs.

Built-in power amplifier satisfy a small PA system with

170W+170W (4

) output.

Mixing of 4 microphone inputs and 3 stereo (line) inputs

Line input (ST3) can be select 4 AV's one.

Wireless Tuner Unit Can Be Installed

Two UHF SYNTHESIZED TUNER UNIT WRU-806A

can be installed.

Wireless microphone system can be easy to setup.

Wireless Remote Controller supplied

AV input selection, master volume and MUTING can be

controlled.

Simple work of Sony's CD player or MD player, Cassette

Deck can be operated

*

.

*

AV equipment supplied with a wireless remote control or with

Control-S terminal only

Exclusive Input Connectors for Recording Equipment

Line input (ST2) is separated from REC bass to avoid

oscillation comes from flowing of its own signal.

Features

Enough Number of Input/Output Terminals, Various

Function

1

The master input to connect equalizer or limiter.

2

The ECHO SEND/RETURN terminals for connect

Echo equipment

3

The ASSIGN SWITCH cuts the microphone signals

from MASTER OUTPUT.

4

Tone control (BASS, TREBLE), BALANCE switch of

stereo/monaural and MUTING button.

5

The MIC GROUP knob for centralized control of

summing signal from 4 microphone inputs.

6

The CONTROL-S terminal

7

The RS-232C REMOTE terminal

8

EIA standard 19 inch rackmountable (3U high)

Summary of Contents for SRP-X351P















Reviews: