Sony SLV-975HF Operating Instructions Manual Download Page 66

Page: 66 / 90

Additional Operations

SLV-975HF 3-858-120-11 (1)

Recording TV
programs using
the quick timer

After starting recording in the normal way, you can have the VCR stop
recording automatically after a specified duration.

While recording, press QUICK TIMER once.

Press QUICK TIMER repeatedly to set the duration.

Each press advances the time in increments of 30 minutes.

The duration decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.

To check or extend the duration

Press QUICK TIMER once. The duration is displayed for 10 seconds. If you
want to extend the time, press QUICK TIMER within 10 seconds to set to the
new duration.

To stop while recording

Press

STOP.

Using the quick timer during stop mode

Press QUICK TIMER.

Press CH +/– or INPUT SELECT to select the channel you want to
record.

Press QUICK TIMER repeatedly to set the recording duration.
The recording starts.

QUICK TIMER

0:00

0:30

1:00

10:30

11:00

Summary of Contents for SLV-975HF



























































































Search results

Summary of Contents for SLV-975HF

Reviews:

Related manuals for SLV-975HF

Brands by name

Popular brands

Sony SLV-975HF, Operating Instructions Manual

Search results

Summary of Contents for SLV-975HF

Reviews:

Related manuals for SLV-975HF

Brands by name

Popular brands