background image

2

WARNING

WARNING

To prevent fire or shock hazard, do not 
expose the unit to rain or moisture.

This symbol is intended to alert the user 
to the presence of uninsulated 
“dangerous voltage” within the product’s 
enclosure that may be of sufficient 
magnitude to constitute a risk of electric 
shock to persons.

This symbol is intended to alert the user 
to the presence of important operating 
and maintenance (servicing) instructions 
in the literature accompanying the 
appliance.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH 
WIDE BLADE OF PLUG TO WIDE SLOT, 
FULLY INSERT.

Precautions

Safety

• Operate the unit only on 120 V AC, 60 Hz.
• If anything falls into the cabinet, unplug the unit 

and have it checked by qualified personnel before 
operating it any further.

• This unit is not disconnected from the AC power 

source (mains) as long as it is connected to the 
wall outlet, even if the unit itself has been turned 
off.

• Unplug the unit from the wall outlet if you do not 

intend to use it for an extended period of time.  To 
disconnect the cord, pull it out by the plug, never 
by the cord.

• One blade of the plug is wider than the other for 

the purpose of safety and will fit into the power 
outlet only one way.  If you are unable to insert 
the plug fully into the outlet, contact your Sony 
dealer.

Installing

• Allow adequate air circulation to prevent internal 

heat buildup.

• Do not place the unit on surfaces (rugs, blankets, 

etc.) or near materials (curtains, draperies) that 
may block the ventilation slots.

• Do not install the unit near heat sources such as 

radiators or air ducts, or in a place subject to 
direct sunlight, excessive dust, mechanical 
vibration or shock.

• Do not install the unit in an inclined position.  It 

is designed to be operated in a horizontal position 
only.

• Keep the unit and cassettes away from equipment 

with strong magnets, such as microwave ovens or 
large loudspeakers.

• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to a 

warm location, moisture may condense inside the 
VCR and cause damage to the video head and 
tape.  When you first install the unit, or when you 
move it from a cold to a warm location, wait for 
about three hours before operating the unit.

Information

For customers in the USA

CAUTION

You are cautioned that any changes or modifications 
not expressly approved in this manual could void 
your authority to operate this equipment.

NOTE:

This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable 
protection against harmful interference in a 
residential installation.
This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used 
in accordance with the instructions, may cause 
harmful interference to radio communications.
However, there is no guarantee that interference will 
not occur in a particular installation.  If this 
equipment does cause harmful interference to radio 
or television reception, which can be determined by 
turning the equipment off and on, the user is 
encouraged to try to correct the interference by one 
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment 

and receiver.

• Connect the equipment into an outlet on a circuit 

different from that to which the receiver is 
connected.

• Consult the dealer or an experienced radio/TV 

technician for help.

Owner’s record

The model and serial numbers are located at the rear 
of the unit.
Record these numbers in the spaces provided below. 
Refer to them whenever you call upon your Sony 
dealer regarding this product.
Model No._________________________
Serial No._________________________

Summary of Contents for N900 - SLV - VCR





















































































Reviews: