background image

1-1

MVS-8000SF

Section 1

Installation

1-1. Operating Environment

Operating guaranteed temperature :

+

d

C to 

+

40 

d

C

Performance guaranteed temperature :

+

10 

d

C to 

+

35 

d

C

Operating humidity :

10 % to 90 %
(relative humidity)

Storage temperature :

_

20 

d

C to 

+

60 

d

C

Mass :

Approx. 45 kg
(when all options
are installed)

Prohibited locations for installation

.

Areas where the unit will be exposed do direct sunlight
or any other strong lights.

.

Dusty areas

.

Areas subject to vibration.

.

Areas with strong electric or magnetic fields.

.

Areas near heat sources.

.

Areas subject to electrical noise.

.

Areas subject where is subjected to static electricity.

Ventilation

The inside of the MVS8000SF-C is cooled by a fan (on
both sides).
The power supply can be damaged if the exhaust vent (on
both sides) and air intake (front panel) are blocked or the
fan is stopped.
Therefore, leave a blank space of more than 10 cm in the
front and back of the MVS8000SF-C.

1-2. Power Supply

1-2-1. Power Specifications

A switching regulator is used for the power supply of this
unit. The voltage within the range of 100 V to 240 V can
be used without changing the supply voltage.

Power requirements :

AC 100 to 240 V 

±

10 %

Power frequency :

50/60 Hz

Current consumption : 100 V : 10 A,  240 V : 4.2 A

(with all options installed)

m
.

As the inrush current at turn-on is a maximum 60 A (at
100 V)/110 A (at 230 V), the capacity of the AC power
source must be commensurate with this load.
If the capacity of the AC power is not adequately large,
the AC power source braker will operate or the unit will
abnormally operate.

.

This system contains the two power supply units as the
standard configuration. A fourth, redundant, power
supply may be installed as an option.
When starting up this system, be sure to turn on the
power of all the power supply units.

1-2-2. Recommended Power Cord

w
.

The power cord is not supplied with the MVS8000SF-C.
Be sure to use the power cord that is applicable to places
in the area.
To avoid a fire or an electric shock, be sure to use the
designated power cord.

.

Do not damage the power cord otherwise a fire or
electric shock may result.

 For customers in the U.S.A. and Canada

1

  Power cord, 125 V  10 A (2.4 m) : 

!

 1-557-377-11

AC inlet

1

 For customers in the all European countries

1

  Power cord, 250 V  10 A (2.4 m) : 

!

 1-782-929-21

1

AC inlet

Summary of Contents for MVS8000SF-C









































































Reviews: