background image

English

• This lamp is designed for use with the Sony projector.
• Be sure to confirm that this lamp is usable with your projector

before using it by reading the Operating Instruction or
Installations Manual for Dealers supplied with your projector.

About lamp replacement

Attaching the lamp may cause fire or injury to persons.
Users should ask a qualified Sony representative to attach the
lamp.

Replacing the lamp unit

Note

• Before replacing the lamp unit, be sure to turn off the

projector and disconnect the power cord of the projector.
When replacing the lamp unit after using the projector, wait at
least one hour to allow the lamp unit to cool.

• Whenever you replace the lamp unit, be sure to replace the

air filter with a new one.

The illustrations below show the case of replacing the lamp unit
with the projector installed on the ceiling.

1

Loosen the two screws fixing the top panel at the rear of
the projector using the supplied screwdriver (

1

), then

slide the top cover backward and lift it to remove (

2

).

1

2

2

Loosen the two screws fixing the lamp cover using the
supplied screwdriver to remove the lamp cover.

3

Loosen the three screws with a Phillips screwdriver.

4

Holding the lamp unit with your hand, push back the
stoppers on the left and right sides, then pull out the
lamp unit.

5

Insert the new lamp unit straight all the way in until it is
securely in place, and pull out both the stoppers until
you hear a click.

6

Tighten the three screws loosen in step 3 to secure the
lamp unit to the projector.

7

Replace the lamp cover and tighten the two screws.

8

Replace the top panel and tighten the two screws.

9

Connect the power cord and set the projector to standby
mode.

10

Press the RESET, 

<

,

, and ENTER buttons on the

remote control in this order for less than five seconds
each.

Specifications

Dimensions

180 

×

 157 

×

 163 mm

(7 

1

/

8

 

×

 6 

1

/

4

 

×

 6 

1

/

2

 inches) (w/h/d)

Mass

1.8 kg (3 lb 15 oz)

Supplied accessories

Screwdriver (1)
Operating Instructions (1)

Summary of Contents for LMP-H700

Page 1: ...まち がった使いかたをすると 火災や人身事故につながることがあり 危 険です 事故を防ぐために次のことを必ずお守りください 安全のための注意事項を守る 破損したら使わずに お買い上げ店またはテクニカルインフォメー ションセンターに修理を依頼する この表示の注意事項を守らないと 事 故によりけがをしたり周辺の物品に損 害を与えたりすることがあります 警告表示の意味 この取扱説明書および製品では 次のような表示をしています 表示の内容を よく理解してから本文をお読みください 行為を指示する記号 行為を禁止する記号 注意を促す記号 この表示の注意事項を守らないと 火 災や高温などにより死亡や大けがなど 人身事故につながることがあります 日本語 ランプの交換のしかた ご注意 ランプを交換する場合は 必ずプロジェクターの電源を切り 電源 コードを抜いてから行ってください また プロジェクターを使用し...

Page 2: ...xing the top panel at the rear of the projector using the supplied screwdriver 1 then slide the top cover backward and lift it to remove 2 1 2 2 Loosen the two screws fixing the lamp cover using the supplied screwdriver to remove the lamp cover 3 Loosen the three screws with a Phillips screwdriver 4 Holding the lamp unit with your hand push back the stoppers on the left and right sides then pull o...

Reviews: