![background image](http://html.mh-extra.com/html/sony/lbt-sh2000/lbt-sh2000_operating-instructions-manual_1329858032.webp)
model name [LBT-SH2000]
[4-273-674-
81
(1)] US
32
US
filename[D:\NORM'S JOB\SONY HA\SO120012\LBT-
SH2000\4273674811_US\US080ADD.fm]
masterpage:Left
On safety
• Completely disconnect the power cord (mains
lead) from the wall outlet (mains) if it is not
going to be used for an extended period of
time. When unplugging the unit, always grip
the plug. Never pull the cord itself.
• Should any solid object or liquid get into the
system, unplug the system, and have it
checked by qualified personnel before
operating it again.
• AC power cord must be changed only at the
qualified service shop.
• Avoid looking directly at the lighting on the
LED speakers for too long. Doing so may be
harmful to your health.
On placement
• Do not place the system in an inclined
position or in locations that are extremely hot,
cold, dusty, dirty, or humid or lacking
adequate ventilation, or subject to vibration,
direct sunlight or a bright light.
• Be careful when placing the unit or speakers
on surfaces that have been specially treated
(for example, with wax, oil, polish) as staining
or discoloration of the surface may result.
• If the system is brought directly from a cold to
a warm location or is placed in a very damp
room, moisture may condense on the lens
inside the unit, and cause the system to
malfunction. In this situation, remove the
disc, and leave the system turned on for about
an hour until the moisture evaporates.
On heat buildup
• Heat buildup on the unit during operation is
normal and is not a cause for alarm.
• Do not touch the cabinet if it has been used
continuously at a high volume because the
cabinet may have become hot.
• Do not obstruct the ventilation holes.
On the speaker system
This speaker system is not magnetically
shielded, and the picture on nearby TV sets may
become magnetically distorted. In this situation,
turn off the TV, wait 15 to 30 minutes, and turn
it back on. If there is no improvement, move the
speakers far away from the TV.
Cleaning the cabinet
Clean this system with a soft cloth slightly
moistened with a mild detergent solution.
Do not use any type of abrasive pad, scouring
powder, or solvent, such as thinner, benzine,
or alcohol.
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 4 ohm loads, both channels driven,
from 120 – 10,000 Hz; rated 240 watts per
channel minimum RMS power, with no
more than 0.7% total harmonic distortion
from 250 milliwatts to rated output.
Amplifier section
The following are measured at AC 120 V,
60 Hz
Power output (rated):
High channel
300 W + 300 W (at 4
:
, 1 kHz,
1% THD)
Low channel
300 W + 300 W (at 4
:
, 100 Hz,
1% THD)
RMS output power (reference):
High channel
500 W + 500 W (per channel at 4
:
,
1 kHz)
Low channel
500 W + 500 W (per channel at 4
:
,
100 Hz)
Inputs
PC (AUDIO IN) L/R, TV (AUDIO IN) L/R,
DVD/SAT (AUDIO IN) L/R, GAME
(AUDIO IN) L/R
Voltage 2 V, impedance 47 k
:
MIC
Sensitivity 1 mV, impedance 10 k
:
A,
B port: Type A
USB section
Supported bit rate
MP3 (MPEG 1 Audio Layer-3):
32 kbps – 320 kbps, VBR
WMA: 48 kbps – 192 kbps
AAC: 48 kbps – 320 kbps