Sony KP-41T65C Service Manual Download

Page: 20 / 88

– 20 –

-EN

Operations

Operating a VCR

To turn on or off
To select a channel
directly
To change channels
To record

To play
To stop
To fast forward
To rewind the tape
To pause

To search the picture
forward or backward

To change input mode

Operating video equipment

Use the video operating buttons on the remote
control to operate the video equipment.
Press VTR (FUNCTION) before operating the
video equipment.

VTR (POWER)

ENTER

0 – 9 buttons

CH +/–

VTR (FUNCTION)

Video operating

buttons

Buttons on the remote control

Press VTR (POWER).
Press the 0 – 9 buttons.

Press CH +/–.
Press

(

while pressing

. First release

(

, then release

Press

(

Press

)

Press

To resume normal playback, press again.
Press

)

during playback.

To resume normal playback, release the
button.
Press TV/VTR.

Buttons on the remote control

Press VTR (POWER).
Press

(

Press

To resume normal playback, press again.
Keep pressing

)

during

playback.
To resume normal playback, release the
button.
Press CH +/–.

Operating an MDP

To turn on or off
To play
To stop
To pause

To search the picture
forward or backward

To search the chapter
forward and backward

N o t e

• If the video equipment does not have a certain function, the

corresponding button on this remote control will not operate.

MDP manufacturer code numbers

Manufacturer

Code number

Sony

701

Kenwood

707

Magnavox

703

Maranz

702

Mitsubishi

702

Panasonic

704

Philips

703

Pioneer

702

RCA

702

Sanyo

706

Sharp

705

Yamaha

703

Notes

• If more than one code number is listed, try entering them one

by one, until you come to the correct code for your equipment.

• In some rare cases, you may not be able to operate your non-

Sony video equipment with the supplied remote control. This
is because your equipment may use a code that is not included
with this remote control. In this case, please use the
equipment’s own remote control unit.

• The code numbers for Sony equipment are assigned at the

factory as follows:
VHS VCR

301 (preset code for the supplied

remote control)

8 mm VCR

302

Beta, ED Beta VCRs

303

• Whenever you remove the batteries — to replace them, for

example — if too much time is taken, the code number may
revert to the factory setting and must be reset.

-EN

Operations

ENTER

CODE SET

DBS/CABLE

FUNCTION

DBS/CABLE

FUNCTION

DBS/CABLE

Press DBS/CABLE (POWER) to turn on the
cable box or DBS receiver.

Use the cable box/DBS control buttons to
check if the code number works.

For example, to operate a cable box or DBS receiver,
you can use the DBS/CABLE (POWER), JUMP, CH
+/–, 0 – 9 and ENTER buttons.

N o t e

• If the cable box or DBS receiver does not have a certain

function, the corresponding button on this remote control will
not operate.

To operate the projection TV

Press TV (FUNCTION). Then use the projection TV
control buttons to control the projection TV.

For more details on operating the cable box or
DBS receiver

Refer to the operating instructions that come with the
equipment.

If the remote control doesn’t work

• First, try repeating the setup procedures using the other codes

listed for your equipment.

Manufacturer code numbers (cable box)

Notes

• If more than one code number is listed, try entering them one

by one until you come to the correct code for your equipment.

• If you enter a new code number, the code number you

previously entered at that setting is erased.

• In some rare cases, your equipment may use a code that is not

provided with this remote control and you may not be able to
operate your equipment with the supplied remote control. In
this case, use the equipment’s own remote control unit.

• Whenever you remove the batteries — to replace them, for

example — if too much time is taken, the code numbers may
revert to the factory setting and must be reset.

Manufacturer

Hamlin/Regal
Jerrold/G. I.

Oak
Panasonic
Pioneer
Scientific Atlanta
Tocom
Zenith

Manufacturer code numbers (DBS receiver)

Manufacturer

Sony

RCA

Code number

801 (preset code for the supplied

remote control)

802

Code number

222, 223, 224, 225, 226
201, 202, 203, 204, 205, 206, 207, 208,
218
227, 228, 229
219, 220, 221
214, 215
209, 210, 211
216, 217
212, 213

You can program the supplied remote control to
operate a cable box or DBS receiver. Follow the
procedures below to set the manufacturer’s code
number in the remote control.

* The TV/DBS, GUIDE, DISPLAY,

, and MENU

buttons can be used only with a DBS receiver.

Turn off the equipment you want to set up,
and press DBS/CABLE (FUNCTION).

Press the CODE SET, DBS/CABLE (FUNCTION),
and 0 – 9 buttons to enter the
manufacturer’s code number (see the chart
on the right column), then press ENTER. For
example, to program your remote control
to operate a Sony DBS receiver, press CODE
SET, DBS/CABLE (FUNCTION), 8, 0, 1, and
ENTER.

Operating a cable
box or DBS receiver

DBS/CABLE (POWER)

DBS/CABLE

(FUNCTION)

0 – 9 buttons

ENTER
GUIDE*