Sony IT-M804 Operating Instructions Manual Download Page 28

Page: 28 / 80

Basics

Pick up the handset (or press

(SPEAKERPHONE)

“=== TALK ===” appears on
the display, and then the
operation duration in hours,
minutes and seconds is
displayed.

The connected line button lights
up.

When you want to select the line
beforehand, press

(LINE 1)

(LINE 2)

(LINE 3)

(LINE 4)

The corresponding line button
lights up.

Dial the phone number.

The phone number dialed
appears on the display.

When you’re done talking,
replace the handset in the cradle
(or press

(SPEAKERPHONE)

The disconnected line button
goes off.

Note

If there is a line put on hold, you cannot make a call by just picking up the
handset and pressing

(SPEAKERPHONE)

in step 1. Press a line button that is not

used first, and then dial the phone number.

Tip

If you pick up the handset during speakerphone conversation, it will change to
handset conversation, and conversely when you press

(SPEAKERPHONE)

during handset conversation, it becomes speakerphone conversation.

Basics

Making calls

TONE

(*)

(HOLD)

(SPEAKERPHONE)

(LINE 1)

(MUTING)

(REDIAL/PAUSE)

(BUSY REDIAL)

(VOLUME)

(LINE 2)

(LINE 3)

(LINE 4)

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands