11
Locations and Functions of Parts
d
MENU control block
• DISP/MENU (display/menu) lever and indicator
Selects the status display or setup menu display. In setup
menu mode, the indicator turns on.
• CANCEL/ENTER lever
In setup menu mode, used to cancel and enter settings.
• CONTROL knob (rotary encoder)
In status screen mode, used to change the displayed page.
In setup menu mode, used to move the cursor on a page and
to change menu settings. Pressing the CONTROL knob
performs the same function as setting the CANCEL/ENTER
lever to the ENTER position.
e
POWER switch
Switches the power for the entire system on and off, including
the CCU, camera, and the RCP-1000-series Remote Control
Panel connected to the REMOTE connector on the rear panel.
Pressing the “
?
” side turns the camera system on, and
pressing the “
a
” side turns it off.
f
POWER indicator
CAM
: Turns on when power is supplied to the camera.
MAIN
: Turns on when the CCU power supply is turned on. It
flashes when there is a problem with the fan.
g
NETWORK indicator
Displays the network system connection status.
On
: Indicates that external control equipment (MSU-
1000/1500 Master Setup Unit, RCP-1000-series Remote
Control Panel, or other device) is connected.
Flashing
: Indicates a connection problem with the external
control equipment (MSU-1000/1500 Master Setup Unit,
RCP-1000-series Remote Control Panel, or other device).
Off
: Indicates that a LAN cable is not connected or that the
network system connection parameters have not been set.
See “Network diagnostics” on page 16 and “NETWORK
SETTINGS menu” on page 28.
Rear Panel
a
SDI OUTPUT 1 to 4 connectors (BNC type)
Outputs the camera signals in HD SDI or SD SDI signal
format.
The SDI OUTPUT 3 and SDI OUTPUT 4 connectors can also
output signals with superimposed character or marker display.
b
VBS OUTPUT 1, 2 (composite video signal 1, 2)
connectors (BNC type)
Outputs (2-system) the camera signals in composite signal
format.
c
LAN jack (RJ-45, 8-pin)
Connects to a LAN hub (10BASE-T/100BASE-TX), when
using a network connection, via a LAN cable (shielded type,
category 5 or higher).
• For safety, do not connect the connector for peripheral device wiring
that might have excessive voltage to this port. Follow the
instructions for this port.
• When you connect the LAN cable of the unit to peripheral device,
use a shielded-type cable to prevent malfunction due to radiation
noise.
• Par mesure de sécurité, ne raccordez pas le connecteur pour le
câblage de périphériques pouvant avoir une tension excessive à ce
port. Suivez les instructions pour ce port.
• Aus Sicherheitsgründen nicht mit einem Peripheriegerät-Anschluss
verbinden, der zu starke Spannung für diese Buchse haben könnte.
Folgen Sie den Anweisungen für diese Buchse.
d
PROMPTER (teleprompter input) connectors
(BNC type)
Inputs the VBS signal for the teleprompter. The input signal is
output from the other connector as-is (loop-through output). If
the loop-through output is not used, connect it to a 75
Ω
terminator.
e
PIX (picture monitor output) connector (BNC type)
Outputs a video signal for a picture monitor. It can also output
a signal with superimposed character display.
f
WF (waveform monitor output) connector (BNC type)
Outputs a video signal for a waveform monitor.
DISP/MENU (display/menu) lever and indicator
CANCEL/ENTER lever
CONTROL knob
a
l m
n o
p q r
s
b c d e fgh
i
j
k
CAUTION
ATTENTION
VORSICHT