background image

HT-NT5

2

NOTES  ON  CHIP  COMPONENT  REPLACEMENT

•  Never reuse a disconnected chip component.
•  Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

FLEXIBLE  CIRCUIT  BOARD  REPAIRING

•  Keep the temperature of soldering iron around 270 °C during 

repairing.

•  Do not touch the soldering iron on the same conductor of the 

circuit board (within 3 times).

•  Be careful not to apply force on the conductor when soldering 

or unsoldering.

SAFETY  CHECK-OUT

After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, 
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.

LEAKAGE  TEST

The AC leakage from any exposed metal part to earth ground and 
from all exposed metal parts to any exposed metal part having a 
return to chassis, must not exceed 0.5 mA (500 microamperes.). 
Leakage current can be measured by any one of three methods.
1.  A commercial leakage tester, such as the Simpson 229 or RCA 

WT-540A. Follow the manufacturers’ instructions to use these 
instruments.

2.  A battery-operated AC milliammeter. The Data Precision 245 

digital multimeter is suitable for this job.

3.  Measuring the voltage drop across a resistor by means of a 

VOM or battery-operated AC voltmeter. The “limit” indication 
is 0.75 V, so analog meters must have an accurate low-voltage 
scale. The Simpson 250 and Sanwa SH-63Trd are examples 
of a passive VOM that is suitable. Nearly all battery operated 
digital multimeters that have a 2 V AC range are suitable. (See 
Fig. A)

1.5 k

Ω

0.15 

μ

F

AC

voltmeter

(0.75 V)

To Exposed Metal

Parts on Set

Earth Ground

Fig. A.  Using an AC voltmeter to check AC leakage.

SAFETY-RELATED  COMPONENT  WARNING!

COMPONENTS  IDENTIFIED  BY  MARK  

0

  OR  DOTTED  LINE  

WITH  MARK  

0

  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  

THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS 

 

WHOSE  PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  
MANUAL  OR  IN  SUPPLEMENTS  PUBLISHED  BY  SONY.

ATTENTION  AU  COMPOSANT  AYANT  RAPPORT  

À  LA  SÉCURITÉ!

LES  COMPOSANTS  IDENTIFIÉS  PAR  UNE  MARQUE  

0

  SUR  

LES  DIAGRAMMES  SCHÉMATIQUES  ET  LA  LISTE  DES  
PIÈCES  SONT  CRITIQUES  POUR  LA  SÉCURITÉ  DE  FONC-
TIONNEMENT.  NE  REMPLACER  CES  COMPOSANTS  QUE  
PAR  DES  PIÈCES  SONY  DONT  LES  NUMÉROS  SONT  DON-
NÉS  DANS  CE  MANUEL  OU  DANS  LES  SUPPLÉMENTS  
PUBLIÉS  PAR  SONY.

This system incorporates Dolby* Digital 
and the DTS** Digital Surround System.

*Manufactured under license from Dolby 

Laboratories.
Dolby and the double-D symbol are 
trademarks of Dolby Laboratories.

**For DTS patents, see http://

patents.dts.com. Manufactured under 
license from DTS Licensing Limited. DTS, 
DTS-HD, the Symbol, & DTS and the 
Symbol together are registered 
trademarks of DTS, Inc. © DTS, Inc. All 
Rights Reserved.

The BLUETOOTH

®

 word mark and logos are 

registered trademarks owned by Bluetooth 
SIG, Inc. and any use of such marks by Sony 
Corporation is under license. Other 
trademarks and trade names are those of 
their respective owners.

This system incorporates High-Definition 
Multimedia Interface (HDMI™) technology. 
The terms HDMI and HDMI High-Definition 
Multimedia Interface, and the HDMI Logo 
are trademarks or registered trademarks of 
HDMI Licensing LLC in the United States 
and other countries.

The N Mark is a trademark or registered 
trademark of NFC Forum, Inc. in the United 
States and in other countries.

Android and Google Play are trademarks of 
Google Inc.

Google Cast and the Google Cast badge 
are trademarks of Google Inc.

“Xperia” is a trademark of Sony Mobile 
Communications AB.

Apple, the Apple logo, iPhone, iPod, iPod 
touch, and Retina are trademarks of Apple 
Inc., registered in the U.S. and other 
countries. App Store is a service mark of 
Apple Inc.

“Made for iPod,” and “Made for iPhone” 
mean that an electronic accessory has 
been designed to connect specifically to 
iPod or iPhone, respectively, and has been 
certified by the developer to meet Apple 
performance standards. Apple is not 
responsible for the operation of this device 
or its compliance with safety and 
regulatory standards. Please note that the 
use of this accessory with iPod or iPhone 
may affect wireless performance.

“BRAVIA” logo is a trademark of Sony 
Corporation.

“Cle” is a trademark of Sony 
Corporation.

“PlayStation

®

” is a registered trademark of 

Sony Computer Entertainment  Inc.

MPEG Layer-3 audio coding technology 
and patents licensed from Fraunhofer IIS 
and Thomson.

Windows Media is either a registered 
trademark or trademark of Microsoft 
Corporation in the United States and/or 
other countries.
This product is protected by certain 
intellectual property rights of Microsoft 
Corporation. Use or distribution of such 
technology outside of this product is 
prohibited without a license from Microsoft 
or an authorized Microsoft subsidiary.

Opera® Devices SDK from Opera Software 
ASA. Copyright 1995-2015 Opera Software 
ASA. All rights reserved.

Wi-Fi®, Wi-Fi Protected Access®, Wi-Fi 
Alliance® and Wi-Fi CERTIFIED Miracast® 
are registered trademarks of Wi-Fi Alliance.

Wi-Fi CERTIFIED™, WPA™, WPA2™, Wi-Fi 
Protected Setup™ and Miracast™ are 
trademarks of Wi-Fi Alliance.

Copyrights and Trademarks

LDAC™ and LDAC logo are trademarks of 
Sony Corporation.

LDAC is an audio coding technology 
developed by Sony that enables the 
transmission of High-Resolution (Hi-Res) 
Audio content, even over a Bluetooth 
connection. Unlike other Bluetooth 
compatible coding technologies such as 
SBC, it operates without any down-
conversion of the Hi-Res Audio content*, 
and allows approximately three times 
more data** than those other technologies 
to be transmitted over a Bluetooth wireless 
network with unprecedented sound 
quality, by means of efficient coding and 
optimized packetization.

*excluding DSD format contents

**in comparison with SBC (Subband 

Coding) when the bitrate of 990 kbps 
(96/48 kHz) or 909 kbps (88.2/44.1 kHz) is 
selected

This product contains software that is 
subject to the GNU General Public License 
(“GPL”) or GNU Lesser General Public 
License (“LGPL”). These establish that 
customers have the right to acquire, 
modify, and redistribute the source code of 
said software in accordance with the terms 
of the GPL or the LGPL.

For details of the GPL, LGPL and other 
software licenses, please refer to [Software 
License Information] in [System Settings] of 
the [Setup] menu on the product.

The source code for the software used in 
this product is subject to the GPL and LGPL, 
and is available on the Web. To download, 
please access the following:
URL: 
http://oss.sony.net/Products/Linux

Please note that Sony cannot answer or 
respond to any inquiries regarding the 
content of this source code.

“DSEE HX” is a trademark of Sony 
Corporation.

DLNA™, the DLNA Logo and DLNA 
CERTIFIED™ are trademarks, service marks, 
or certification marks of the Digital Living 
Network Alliance.

“TRILUMINOS” and “TRILUMINOS” logo are 
a registered trademark of Sony 
Corporation.

This product incorporates Spotify software 
which is subject to 3rd party licenses found 
here*:
https://developer.spotify.com/esdk-
third-party-licenses/

Spotify and Spotify logos are trademarks of 
the Spotify Group.*

*Depending on the country and region, 

this function may not be available.

All other trademarks are trademarks of 
their respective owners.

Ver. 1.2

Summary of Contents for HT-NT5











































































Reviews: