5(GB)
0
Audio channel 3/4 level meters
Indicate the level of the signal input to the AUDIO IN
CH-3 and CH-4 connectors or the level of the audio
playback signal.
!¡
LIGHT switch
Turns the display panel illumination on and off.
ON: Turns the illumination on.
OFF: Turns the illumination off.
!™
AUDIO LEVEL CH-3/4 (audio channel 3/4
recording level) controls
These controls adjust the audio level of channels 3 and
4 when you set the AUDIO SELECT CH-3/4 switches
to MANUAL.
!£
AUDIO SELECT CH-3/4 switches
These switches set the audio level adjustment to
AUTO or MANUAL for channels 3 and 4.
AUTO: Audio level is adjusted automatically.
MANUAL: Audio level is adjusted manually by the
AUDIO LEVEL CH-3 or 4 control.
!¢
MONITOR switches
Select the audio output to the AUDIO OUT connector
or headphones (audio channels 1, 2, 3 or 4).
Use the left switch to select CH 1/2 (audio channels 1
and 2) or CH 3/4 (audio channels 3 and 4), and the
right switch to select ST (two-channel stereo output) or
MONO (single-channel monaural output) for the
selected channels.
!∞
POWER switch
Turns the power to the HDCA-901 on and off. Can be
used to reduce power consumption by supplying power
only to the audio circuits when the output from the HD
SDI circuits is not being monitored.
ON ALL: Supplies power to all circuits.
ON SEL: Supplies power only to the audio circuits,
(power for HD SDI output is cut). Supplying
power only to the HD SDI output circuits while
cutting power to the audio circuits is also possible.
For details, refer to the supplied Maintenance Manual.
OFF: Turns the HDCA-901 off. In this case, the
HDW-F900 can be independently turned on and
off using the POWER switch on the HDW-F900.
Note
When the POWER switch on the HDCA-901 is set to
ON ALL or ON SEL, the POWER switch on the
HDW-F900 controls the power supply to both the
camcorder and camera adaptor at the same time.
1
Battery attachment
Attaches a BP-L60A Battery Pack.
For details on inserting batteries, refer to the Operation
Manual of the HDW-F900.
2
PHONES (headphones) jack
Connects stereo headphones with an impedance of 8
ohms.
3
PHONES LEVEL (headphone output level)
control
Adjusts the headphone volume.
4
AUDIO IN CH-3/CH-4 LINE/MIC/+48 V ON
(audio input channel 3/4 line input/microphone
input/external power 48 V on) switches
Specifies the audio source or microphone connected to
the AUDIO IN CH-3/CH-4 connectors.
LINE: Line input audio equipment
MIC: A microphone with internal batteries
+48 V ON: A microphone with an external power
supply
5
AUDIO IN CH-3/CH-4 (audio channels 3 and 4)
connectors (XLR type, 3-pin, female)
Connect an audio source or microphone.
Combined with the AUDIO IN CH-1/CH-2 connectors
on the HDW-F900, a total of four audio inputs are
provided.
6
AUDIO OUT (audio output) connector (XLR
type, 5-pin, male)
Outputs the audio signal selected with the MONITOR
switch.
7
HD SDI OUT 1/2 connectors (BNC-type)
Output two channels of HD SDI video/audio signals.
8
DC IN (DC power input) connector (XLR type,
4-pin, male)
Connect an AC adaptor or an external battery through
a DC output cable. Power input to the HDCA-901 is
supplied to the HDW-F900.
9
DC OUT (DC power output) connector (4-pin)
Supplies power to an optional WRR-860A UHF
Synthesized Diversity Tuner. Use this connector when
an optional battery and the tuner are attached to the
HDCA-901 and the tuner’s power cord cannot reach
the DC OUT connector on the rear of the HDW-F900.
Summary of Contents for HDCA-901
Page 18: ......
