![background image](http://html.mh-extra.com/html/sony/hcd-vz50md/hcd-vz50md_service-manual_1329759030.webp)
30
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
1
Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.)
2
Move the multi-stick and display “CPLAY1MODE”(C34).
3
Press the PUSH ENTER button to change the display to “CPLAY1MID”.
4
When access completes, the display changes to “C =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
1
Press the PUSH ENTER button during continuous playback to change the display as below.
When pressed another time, the parts to be played back can be moved.
2
When access completes, the display changes to “C =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
1
Press the CLEAR button while REC IT is lit. The display will change to “CPLAY1MODE”(C34).
2
To remove the disc, press the MD
Z
button while REC IT is off.
Note : The playback start addresses for IN, MID, and OUT are as follows.
IN
40h cluster
MID 300h cluster
OUT 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)
1. Entering the continuous recording mode
1
Set a recordable disc in the unit.
2
Move the multi-stick and display “CREC 1MODE” (C35).
3
Press the PUSH ENTER button to change the display to “CREC 1MID”.
4
When access completes, the display changes to “CREC1 (
)” and
MD REC
lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
1
When the PUSH ENTER button is pressed during continuous recording, the display changes as below.
When pressed another time, the parts to be recorded can be changed.
MD REC
goes off.
2
When access completes, the display changes to “CREC 1(
)” and
MD REC
lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
1
Press the CLEAR button while REC IT is lit. The display changes to “CREC 1MODE” (C35 ) and
MD REC
goes off.
2
To remove the disc, press the MD
Z
button while REC IT is off.
Note 1 : The recording start addresses for IN, MID, and OUT are as follows.
IN
40h cluster
MID
300h cluster
OUT
700h cluster
Note 2 : Press the CLEAR button while REC IT is lit can be used to stop recording anytime.
Note 3 : Do not perform continuous recording for long periods of time above 5 minutes.
Note 4 : During continuous recording, be careful not to apply vibration.
“CPLAY1MID”
t
“CPLAY1OUT”
t
“CPLAY1IN”
“CREC 1MID”
t
“CREC 1OUT”
t
“CREC 1IN”
Summary of Contents for HCD-VZ50MD
