![background image](http://html.mh-extra.com/html/sony/hcd-rg190/hcd-rg190_service-manual_420841004.webp)
4
HCD-RG190/RG290
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40
°
C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
RELEASING THE ANTITHEFT LOCK
The disc table lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure :
1. Press the
I
/
1
button to turn the power on.
2. While pressing the
s
button, press the
A
button until
“UNLOCKED” displayed on the fluorescent indicator tube
(around 5 seconds).
Note:
When “LOCKED” is displayed, the antitheft lock is not released by
turning power on/off with the
I/
1
button.
NOTES ON REPLACEMENT OF IC901 ON THE MAIN
BOARD
IC901 on the MAIN board cannot exchange with single. When IC901
is damaged, exchange the entire mounted board.
MODEL IDENTIFICATION
– Back Panel –
Label indication
Model
2-664-545-0
[]
CED
RG290: AEP, UK
2-664-546-0
[]
E3
RG290: E3
2-664-547-0
[]
SP2
RG290: SP
2-664-548-0
[]
AU
RG290: AUS
2-664-550-0
[]
E51
RG290: E51
2-664-551-0
[]
AR
RG290: AR
2-664-552-0
[]
MX4
RG290: MX
2-664-553-0
[]
CED
RG190: AEP
2-664-554-0
[]
E3
RG190: E3
2-664-555-0
[]
SP2
RG190: SP
2-664-556-0
[]
AU
RG190: AUS
2-664-557-0
[]
EA3
RG190: EA
2-664-558-0
[]
E51
RG190: E51
2-664-559-0
[]
AR
RG190: AR
2-665-213-0
[]
E2
RG190: E2
2-666-351-0
[]
E2
RG290: E2
2-674-578-0
[]
RU
RG290: RU
2-674-579-0
[]
RU
RG190: RU
•
Abbreviation
AR
: Argentina model
AUS
: Australian model
E2
: 120V AC area in E model
E3
: 240V AC area in E model
E51
: Chilean and Peruvian models
EA
: Saudi Arabia model
MX
: Mexican model
Model number label
Ver. 1.1
Summary of Contents for HCD-RG190
Page 20: ...20 HCD RG190 RG290 MEMO ...
Page 125: ...19 HCD RG190 RG290 MEMO ...