![background image](http://html.mh-extra.com/html/sony/hcd-px333/hcd-px333_service-manual_420832089.webp)
89
HCD-PX333
Pin No.
Pin Name
I/O
Description
53
IN-SW
I
Detection input from the tray open/close detect switch (S1) “L”: when tray is close
54
LOD POS
O
CD loading motor (M201) control signal output to the motor driver IC (IC1102)
“L” active *1
55
LOD NEG
O
CD loading motor (M201) control signal output to the motor driver IC (IC1102)
“L” active *1
56
CLP POS
O
Motor control signal output to the motor driver IC “L” active Not used (open)
57
CLP NEG
O
Motor control signal output to the motor driver IC “L” active Not used (open)
58
BVDD
—
Power supply terminal (+5V) (for digital system)
59
BVSS
—
Ground terminal (for digital system)
60 to 73
NC
O
Not used (open)
74
AVDD
—
Power supply terminal (+5V)
75
AVSS
—
Ground terminal
76
AVREF
I
Reference voltage (+5V) input terminal
77 to 80
KEY0 to KEY3
I
Key input terminal (A/D input) Not used (fixed at “H”)
81 to 83
SEL0 to SEL2
I
Model destination setting terminal (A/D input)
84
TEL
I
Tracking error level detection input terminal Not used (open)
85
SEL3
I
Model (CD mechanism deck) destination setting terminal (A/D input)
86
DISC-SENS
I
Detection input from the disc in detect sensor (A/D input) “H”: disc in Not used (open)
87
MECHA-JIGU
I
Not used (open)
88
ADJ
I
Setting terminal for the CD test mode “L”: CD test mode Normally: fixed at “H”
89
I2CHELP
I
Busy signal input for the IIC bus
90
I2CHELP
I
Busy signal input for the IIC bus
91
SCOR
I
Subcode sync (S0+S1) detection signal input from the CD block
92
NC
O
Not used (open)
93
AC-CUT
I
Power off signal input from the system controller (IC501)
94, 95
JOG0, JOG1
I
Rotary encoder jog dial pulse input terminal Not used (fixed at “L”)
96
NC
O
Not used (open)
97
LEDLAT
O
Serial data latch pulse output to a FL driver Not used
98
DRVCS
I
Chip select signal output to a FL driver Not used
99
DRVRST
I
Reset signal output to a FL driver “L”: reset Not used
100
GND
—
Ground terminal
*1 Loading motor (M201) control
Mode
Terminal
LOD NEG (pin
tg
)
“L”
“H”
“L”
“H”
LOD POS (pin
tf
)
“H”
“L”
“L”
“H”
LOADING
EJECT
BRAKE
RUN IDLE
Summary of Contents for HCD-PX333
