![background image](http://html.mh-extra.com/html/sony/hcd-nxm2d/hcd-nxm2d_service-manual_420829022.webp)
22
HCD-NXM2D
Mirr Count
: The number of times which mirror
counts between disc surface and record
surface when disc type judging.
FZC Count
: The number of times which focus zero
cross points of each layer when lens
down.
PI Reference
: The average of PI reference voltage.
(hexadecimal number)
PI Peak
: PI peak level voltage. It performs only
when disc type judgment is successful.
(hexadecimal number)
2-1-2.
Disc Type DVD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: DVD single layer disc (12 cm)
[2]
: DVD dual layer disc (0 layer, 12 cm)
[3]
: DVD dual layer disc (1 layer, 12 cm)
[4]
: DVD-RW disc (12 cm)
[5]
: DVD single layer disc (8 cm)
[6]
: DVD dual layer disc (0 layer, 8 cm)
[7]
: DVD dual layer disc (1 layer, 8 cm)
[8]
: DVD-RW disc (8 cm)
2-1-3.
Disc Type CD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: CD disc (normal speed, 12 cm)
[2]
: CD disc (double speed, 12 cm)
[3]
: CD disc (normal speed, 8 cm)
[4]
: CD disc (double speed, 8 cm)
[5]
: CD-RW disc (normal speed, 12 cm)
[6]
: CD-RW disc (double speed, 12 cm)
[7]
: CD-RW disc (normal speed, 8 cm)
[8]
: CD-RW disc (double speed, 8 cm)
2-1-4.
Disc Type Hybrid
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]
: SACD Hybrid disc (SACD layer, 12 cm)
[2]
: SACD Hybrid disc (CD layer, normal speed, 12 cm)
[3]
: SACD Hybrid disc (CD layer, double speed, 12 cm)
[4]
: SACD Hybrid disc (SACD layer, 8 cm)
[5]
: SACD Hybrid disc (CD layer, normal speed, 8 cm)
[6]
: SACD Hybrid disc (CD layer, double speed, 8 cm)
2-2. Servo Control
Note:
Be sure to perform the disc type setup before performing this item.
Servo Control
1.LD
off R.Sled FWD
2.Focus
off L.Sled REV
3.SPDL
off U.Sled Reset
4.CLVA
off D.Sled Limit
5.Trk.
off
6.Sled
off
7.Fcs.Srch
off
0.All Servo Off
Exit: RETURN
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
[1]
LD
: Turn on/off the laser.
[2]
Focus
: Search the focus and turn on the focus.
[3]
SPDL
: Turn on/off the spindle.
[4]
CLVA
: Turn on/off normal servo of spindle servo.
[5]
Trk.
: Turn on/off the tracking servo.
[6]
Sled
: Turn on/off the sled servo.
[7]
FCS. Srch
: Turn on/off the focus search.
[10/1]
: All servo off.
[R]
Sled FWD (right cursor)
: Move the sled forward.
[L]
Sled REV (left cursor)
: Move the sled reverse.
[U]
Sled FWD (up cursor)
: Reset the sled.
[D]
Sled REV (down cursor) : Limit in the sled.
2-3. Track/Layer Jump
Track/Layer Jump
1. 1Tj
FWD
2. 1Tj
REV
3.500Tj Fine
FWD
4.500Tj Fine
REV
5.10kTj Dirc
FWD
6.10kTj Dirc
REV
7.20kTj Dirc
FWD
8.20kTj Dirc
REV
0. All Servo Off
Exit: RETURN
On this screen, track jump, etc. can be performed. Only for the DVD
dual layer disc, the focus jump and layer jump are displayed in the
right field
[1]
1Tj FWD
: 1 track jump forward.
[2]
1Tj REV
: 1 track jump reverse.
[3]
500Tj FWD
: 500 track jump (fine search)forward.
[4]
500Tj REV
: 500 track jump (fine search) reverse.
[5]
10kTj FWD
: 10k track jump (direct search) forward.
[6]
10kTj REV
: 10k track jump (direct search) reverse.
[7]
20kTj FWD
: 20k track jump (direct search) forward.
[8]
20kTj REV
: 20k track jump (direct search) reverse.
[10/0]
: All servo off.
2-4. Non EEPROM Write Adjust
Non EEPROM Write Adjust
1. Focus Offset
2. Focus Gain
3. Trk.
Offset Coarse
4. Trk.
Offset Fine
5. Trk.
Gain
6. EQ
Boost
0.All Servo Off
Exit: RETURN
On this screen, each item can be adjusted manually. Select the desired
number
[1]
to
[10/0]
from the remote commander, and current setting for
the selected item will be displayed, then increase or decrease numeric
value with the
O
key or
o
key. If CLV has been applied, the jitter is
displayed for reference for the adjustment.
Summary of Contents for HCD-NXM2D
Page 101: ...101 HCD NXM2D MEMO ...