![background image](http://html.mh-extra.com/html/sony/hcd-gx40-electronic-component-system/hcd-gx40-electronic-component-system_service-manual_420766003.webp)
3
HCD-GX40
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
TABLE OF CONTENTS
1. GENERAL
·········································································· 4
2. DISASSEMBLY
································································ 6
2-1. Case (Top) ····································································· 6
2-2. CD Door ········································································ 7
2-3. Front Panel Section ······················································· 7
2-4. CD Mechanism Deck (CDM58F-K6A) ························ 8
2-5. Tape Mechanism Deck (CWL43FF48) ························· 8
2-6. REM Board and PANEL Board ···································· 9
2-7. KEY BOARD Board ····················································· 9
2-8. Back Panel Section ······················································ 10
2-9. SUB TRANS Board and VIDEO OUT Board ············ 10
2-10. MAIN Board ······························································· 11
2-11. AMPLIFIER Board and POWER Board ····················· 11
2-12. TRANS Board ····························································· 12
2-13. CD Board and DRIVER Board ··································· 12
2-14. SPDL Board ································································ 13
2-15. Optical Pick-up (KSM-213D) ····································· 13
2-16. MOTOR Board and ADDRESS SENSOR Board ······· 14
2-17. Table (New), Cam (Control) and
DC Motor (M721) ······················································· 14
3. TEST MODE
···································································· 15
4. ELECTRICAL ADJUSTMENTS
······························· 17
5. DIAGRAMS
······································································ 19
5-1. Circuit Boards Location ·············································· 19
5-2. Block Diagrams ··························································· 20
5-3. Printed Wiring Boards – CD Section (1/2) – ··············· 22
5-4. Printed Wiring Boards – CD Section (2/2) – ··············· 23
5-5. Schematic Diagram – CD Section – ···························· 24
5-6. Printed Wiring Board – MAIN Section – ···················· 25
5-7. Schematic Diagram – MAIN Section (1/4) – ·············· 26
5-8. Schematic Diagram – MAIN Section (2/4) – ·············· 27
5-9. Schematic Diagram – MAIN Section (3/4) – ·············· 28
5-10. Schematic Diagram – MAIN Section (4/4) – ·············· 29
5-11. Printed Wiring Boards – PANEL Section – ················ 30
5-12. Schematic Diagram – PANEL Section – ····················· 31
5-13. Printed Wiring Boards
– POWER/TRANS Section – ······································ 32
5-14. Schematic Diagram
– POWER/TRANS Section – ······································ 33
5-15. Printed Wiring Board – AMPLIFIER Section – ·········· 34
5-16. Schematic Diagram – AMPLIFIER Section – ············ 34
5-17. IC Pin Function Description ········································ 38
6. EXPLODED VIEWS
······················································ 40
6-1. Main Section ······························································· 40
6-2. Front Panel Section ····················································· 41
6-3. MAIN Board Section ·················································· 42
6-4. CD Mechanism Deck Section (CDM58F-K6A) ········· 43
7. ELECTRICAL PARTS LIST
······································· 44
Ver 1.2 2003.11
Summary of Contents for HCD-GX40 - Electronic Component System
Page 57: ...HCD GX40 MEMO 57 ...