Sony HCD-FR10W Page 24 Service Manual Download

Page: 24 / 140

HCD-FR10W

[GENERAL DESCRIPTION]

The Test Mode allows you to make diagnosis and adjustment easily
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).

[TEST DISC LIST]

Use the following test disc on test mode.
TDV-520CSO (DVD-SL)

: PART No. J-2501-236-A

LUV-P01 (CD)

: PART No. 4-999-032-01

TDV-540C (DVD-DL)

: PART No. J-2501-235-A

Note:

Do not use exiting test disc for DVD.

[STARTING TEST MODE]

1. Press the

@/1

button to turn the power on, and set the function

to DVD.

2. Press three buttons of

and

[]

simultaneously

to enter the test mode.

3. It displays “SERVICE IN” on the fluorescent indicator tube,

and displays the Test Mode Menu on the monitor screen as
follows. (At the bottom of the menu screen, the model name
and revision number are displayed)

4. To execute each function, select the desired menu and press

its number on the remote commander (RM-SP350).

5. To release from test mode, press the

@/1

button and turn the

power off.

[OPERATING TEST MODE]

0. SYSCON DIAGNOSIS

The same contents as board detail check by serial interface can be
checked from the remote commander operation.
On the Test Mode Menu screen, press

[0]

key on the remote

commander, and the following Check Menu will be displayed.

0-0. Quit

Quit the Syscon Diagnosis and return to the Test Mode Menu.

Test Mode Menu

0. Syscon Diagnosis

1. Drive Auto Adjustment

2. Drive Manual Operation

3. Mecha Aging

4. Emergency History

5. Mecha Error History

6. Version Information

7. Video Level Adjustment

Exit: POWER Key

Model :DAV-xxx xx

Revision :x.xx

### Syscon Diagnosis ###

Check Menu

0. Quit

1. All

2. Version

3. EEPROM

4. GPIO

5. SD Bus

6. Video

0-1. All (All items continuous check)

This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.

• Example display

For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press the

button to go to the next

item, or press the

button to repeat the same operation again.

To quit the diagnosis and return to Check Menu screen, press the

[RETURN]

key on the remote commander to display Check Menu.

• Error occurred
If an error occurred, the diagnosis is suspended and error is displayed.
Press the

[RETURN]

key on the remote commander to quit the

diagnosis, or press the

button to repeat the same check where

an error occurred, or press the

button to continue the check

from the item next to faulty item.

General Description of Checking Method

Selecting 2 and subsequent items calls the submenu screen of each
item. And selecting 2 and subsequent items executes respective
menus and outputs the results.
For the contents of each submenu, see “Check Items List” as below.

Check Items List:

0-2. Version

0-2-1. All
0-2-2. Revision
0-2-3. ROM Check Sum
0-2-4. Model Type
0-2-5. Region

0-3. EEPROM Check

0-3-1. Sampling Check
0-3-2. Detail Check

0-4. GP I/O Check
0-5. SD Bus Check
0-6. Video Check

0-2. Version

0-2-2.

Revision
The revision number of ROM (IC205) that the program
for the DVD system processor (IC206) is stored.

0-2-3.

ROM Check Sum
Check sum is calculated. (4 digits hexadecimal number)

### Syscon Diagnosis ###