![background image](http://html.mh-extra.com/html/sony/hcd-cpx22-cd-deck-receiver-component/hcd-cpx22-cd-deck-receiver-component_service-manual_420604002.webp)
2
HCD-CPX22/NXM3
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
U.S.A. model:
87.5 – 108.0 MHz (100-kHz step)
Russian model:
65.0 – 74.0 MHz (10-kHz step)
(There is no stereo effect)
87.5 – 108.0 MHz (50-kHz step)
Other models:
87.5 – 108.0 MHz (50-kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Pan-American model:
530 – 1,710 kHz
(with the tuning interval set at 10 kHz)
531 – 1,710 kHz
(with the tuning interval set at 9 kHz)
European, Russian and Saudi Arabian models:
531 – 1,602 kHz
(with the tuning interval set at 9 kHz)
Other models:
531 – 1,602 kHz
(with the tuning interval set at 9 kHz)
530 – 1,710 kHz
(with the tuning interval set at 10 kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
U.S.A. model:
120 V AC, 60 Hz
European and Russian models:
230 V AC, 50/60 Hz
Saudi Arabian model:
120 – 127 V or 220 – 240 V AC,
50/60 Hz
Adjustable with voltage selector
Other models:
120 V, 220 – 240 V AC, 50/60 Hz
Adjustable with voltage selector
Power consumption
U.S.A. model:
65 watts
European and Russian models: 65 watts
0.3 watts (in Power Saving mode)
Other models:
65 watts
Dimensions (w/h/d) incl. projecting parts and controls
Amplifier/Tuner/Tape/CD section:
Approx. 230 x 292 x 355 mm
Mass
Amplifier/Tuner/Tape/CD section:
Approx. 6.1 kg
Supplied accessories
Remote Commander (1)
Size AA (R6) batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Speaker pads (8)
Speaker cords
Design and specifications are subject to change without notice.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
SAFETY CHECK-OUT
To Exposed Metal
Parts on Set
0.15
µ
F
1.5 k
Ω
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
Summary of Contents for HCD-CPX22 - Cd Deck Receiver Component
Page 67: ...67 HCD CPX22 NXM3 MEMO ...