HBD-TZ130
2
Tuner Section
System PLL
quartz-locked
digital
synthesizer
Tuning range
North American and Brazilian models:
87.5 MHz - 108.0 MHz
(100 kHz step)
Other models:
87.5 MHz - 108.0 MHz
(50 kHz step)
Antenna (aerial) terminals
75 ohms, unbalanced
Intermediate frequency
10.7
MHz
Video Section
Outputs
VIDEO: Pin jack
HDMI OUT: HDMI
19-pin
General
Power requirements
North American models:
120 V AC, 60 Hz
Argentine models:
220 V - 240 V AC,
50/60
Hz
Brazilian models:
127 V - 240 V AC,
50/60
Hz
Latin American models:
110 V - 240 V AC,
50/60
Hz
Other models:
220 V - 240 V AC,
50/60
Hz
Power consumption
On: 67 W
Standby:
<1
W*
*
Valid when the system is in the following status:
– [Control for HDMI] is set to [Off].
Dimensions (approx.) 360 mm × 56 mm ×
342 mm (14
1
/
4
in ×
2
1
/
4
in × 13
1
/
2
in) (w/h/d)
incl. projecting parts
Mass (approx.)
2.6 kg (5 lb. 12 oz.)
Design and speci
fi
cations are subject to
change without notice.
SPECIAL COMPONENT NOTICE
The components identi
fi
ed by mark
9
contain con
fi
dential infor-
mation.
Strictly follow the instructions whenever the components are re-
paired and/or replaced.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0
SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
NOTICE POUR COMPOSANTS SPÉCIAUX
Les composants identi
fi
és par la marque
9
contiennent des infor-
mations con
fi
dentielles.
Suivre scrupuleusement les instructions chaque fois qu’un compo-
sant est remplacé et / ou réparé.
Ver. 1.2
SAFETY CHECK-OUT (US MODEL)
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
0.15
μ
F
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
