HBD-E385/E390/T39
27
CONFIRMATION ITEM
1. Playback Operation Con
fi
rmation
1-1. Test Disc
Part No.
Description
Layer
J-6090-199-A
BLX-104
Single Layer
J-6090-200-A
BLX-204
Dual Layer
J-2501-307-A
CD (HLX-A1)
J-2501-305-A
HLX-513
Single Layer (NTSC)
J-2501-306-A
HLX-514
Dual Layer (NTSC)
J-6090-077-A
HLX-506
Single Layer (PAL)
J-6090-078-A
HLX-507
Dual Layer (PAL)
Note:
Refer to the service manual of BDP-BX1/S350 (Part No. 9-883-
989-1
[]
) (page 1-3 to 1-14E) for the use of BLX-104/204.
Operation and Display:
1. BLX-104
Procedure:
1. Select
23.976Hz/1080p.
2. Play “4.Motion picture”.
3. Check whether player can play back or not.
4. Check each outputs.
Video:
Composite/S
Video/component/HDMI.
Audio:
Speaker
out.
* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz)
can use instead of 1080/24p.
However this is temporary correspondence.
* When the output of HDMI is 1080p, the signal of Composite/S
Video/Component are not output.
It is necessary to lower the output of HDMI to 1080i or less.
2. BLX-204
Procedure:
1. Select 1080i (59.94Hz or 50Hz).
2. Play “4.Motion picture”.
3. Check whether player can play back or not.
(Check the picture and sound output)
3. CD (HLX-A1)
Procedure:
Check whether player can play back or not.
(Check the sound output)
4. HLX-513/514 (NTSC), HLX-506/507 (PAL)
Procedure:
1. After displayed Main Menu, select “1.Video Signal”.
2. Play “1.Color bar 100%”.
(Check the picture and sound output)
3. Return to Menu.
4. Play “Demonstration 4:3” or “Demonstration 16:9”.
(Check the picture and sound output)
1-2. Playback operation con
fi
rmation
Con
fi
rm operation in each signal/output mode of test disc (BLX-
104/204) according to the content of the repair.
Note:
“AV Sync.” doesn’t operate.
2. Networking Con
fi
rmation
Con
fi
rm it according to the following procedure when you con
fi
rm
the connection of the network.
Note:
Do not execute “Network Connection Diagnostics” of “Network
Settings” of the home menu with only the router connected.
Procedure:
1. Connect the router with the unit with LAN cable.
2. Turn on the power of the unit and the router.
3. Press the [HOME] button on the remote commander, and the
home menu is displayed.
4. Select “Setup”
“Network Settings”
“Internet Settings”,
and press the [ ] button on the remote commander.
5. Select “View Networks Status” and press the [ ] button on
the remote commander.
6. Con
fi
rm IP address are displayed in “IP Address”, “Subnet
Mask” and “Default Gateway”.
IP Address Setting:
XXXX
Internet Access:
XXXX
Physical Connection:
XXXX
IP Address:
XXX.XXX.XXX.XXX
DNS Settings:
XXXX
MAC Address:
XXX.XXX.XXX.XXX
Primary DNS:
XXX.XXX.XXX.XXX
Secondary DNS:
XXX.XXX.XXX.XXX
Subnet Mask:
XXX.XXX.XXX.XXX
Default Gateway:
XXX.XXX.XXX.XXX
