Sony ExwaveHAD SSC-DC50A, Service Manual

Page: 7 / 64

1-3
SSC-DC50A/54A (UC) SSC-DC50AP/54AP/58AP (CE)
1
2
3
4
8
7
9
!º
5
6
!¡
!™
1
2
4
!º
9
8
5
7
!¡
3
6
1 2 3 4
5
6
SSC-DC50A/50AP
SSC-DC50A/50AP
G
H
I
SSC-DC54A/54AP
4
SSC-DC58AP
1
2
3
6 5
7
8
9
(AC 24 V)/
(24 V CA)/
(AC24V)
1
2
4
3
6
5
7
8
9
(to AC 220 – 240 V)/(vers 220 – 240 V CA)/
(a AC220 – 240V)
J
Connecting the SSC-DC54A/54AP/58AP
Using an external synchronization signal
1
SSC-DC54A/54AP/58AP
7
Sycnchronization output
3
VIDEO OUT connector connector
4 75 ohm coaxial cable 8 Sycnchronization signal (e.g.
5
VIDEO INPUT connector switcher)
6
VS IN connector
9
Power supply
Using an internal synchronization signal
To operate with an internal synchronization signal, set the L.L/INT switch
2
to INT. Connecting the synchronization siganl source (
6
,
7
,
8
) is
not necessary.
Using an AC 24 V power supply (SSC-DC54A/54AP)
• When using a power supply without ground lead (two-lead type),
connect the output of the power supply to the AC 24V 1 and 2 terminals
of the camera.
• When using a power supply with ground lead (three-lead type), connect
the ground lead to the GND terminal and the other two leads to the AC
24V 1 and 2 terminals of the camera.
Phase Adjustment
When using more than one camera, adjust the phase according to the
following procedure.
Vertical phase (L.L mode) (SSC-DC54A/54AP/58AP)
The picture may roll vertically if the vertical phase is not set. Use the
PHASE volume to adjust the vertical phase.
Horizontal phase (VS/VBS lock mode)
The picture may shift horizontally when using an extended cable. Use
the PHASE volume to adjust the horizontal phase.
CCD Characteristics
The following conditions may be observed when using a CCD camera
are not due to any fault within the camera.
Vertical smear
This phenomenon occurs when viewing a very bright object.
Patterned noise
This is a fixed pattern which may appear over the entire monitor screen
when the camera is operated a high temperature.
Jagged picture
When viewing stripes, straight lines, or similar patterns, the image on
the screen may appear jagged.
Installing the camera
When mounting the camera on a tripod, attach the tripod adaptor to
either the top or bottom of the camera. Use a 1/4" UNC-20 screw to
mount the camera on a tripod.
Fitting the camera tripod adaptor
1 Loosen screws
1
–
4
that secure the tripod adaptor. Remove the
adaptor carefully, and do not pull at the screws.
2 Remove screws 5 and 6 .
3 Attach the tripod adaptor on the opposite side, and insert screws
5
and
6
on the surface from which the adaptor was removed.
Connections
Connecting the SSC-DC50A/50AP
Set the MODE switch to B. When the connections have been made, set
the DC 12V power supply switch to ON.
Note
To prevent short circuits, do not let the exposed ends of the mains lead
wires touch each other when connecting to the mains lead terminals.
Using an external synchronization signal
1
SSC-DC50A/50AP (rear)
7
Synchronization signal (e.g., switcher)
2 VIDEO OUT connector 8 Power supply
3
75 ohm coaxial cable
9
DC 12 V switch (set to ON)
4
VIDEO INPUT connector
0
MODE switch (set to B)
5
VS IN connector
!¡
+12 V
6 Synchronization output connector !™ GND (ground)
Using an internal synchronization signal
To operate with an internal synchronization signal, no connection to the
synchronization signal source (
5
,
6
and
7
above) is necessary.
Using a YS-W150/150P/250/250P camera adapter
(not supplied) (Power multiplex)
Set the MODE switch to A. When the connections have been made, set
the YS-W150/150P/250/250P power supply switch to ON.
1
SSC-DC50A/50AP (rear)
7
VIDEO OUT connector
2
DC IN. VS IN/VIDEO OUT
8
VIDEO INPUT connector (monitor
connector input connector)
3
CAMERA IN connector
9
Portable monitor
4
MONITOR OUT connector
0
75 ohm coaxial cable
5 VIDEO INPUT connector !¡ MODE switch (set to A)
6
YS-W150/150P/250/250P
camera adapter
Specifications
Image device 1/2" interline transfer type CCD
Effective picture elements DC50A/54A: 768 (horizontal)
×
494 (vertical)
DC50AP/54AP/58AP: 752 (horizontal)
×
582
(vertical)
Lens mount C-mount/CS-mount adjustable
Signal system DC50A/54A: NTSC color system
DC50AP/54AP/58AP: PAL color system
Synchronization system DC50A/50AP: INT/VBS/VS/MPX-VS
DC54A/54AP/58AP: INT/VBS/VS/Line Lock
External synchronization signal VBS/VS (sync level: 0.3–5.0 Vp-p, 75 ohm)
Horizontal resolution
470 TV lines
Minimum illumination 0.8 lux, F1.2 (with AGC set to ON in TURBO mode)
Video output 1 Vp-p, 75 ohm, negative sync
Video S/N 50 dB or more (with AGC set to OFF, Weight ON)
Electronic shutter 8 levels
1/60 (1/50)
*
, 1/100 (1/120)
*
, 1/250, 1/500,
1/1000, 1/2000, 1/4000, 1/10000
* Numbers within the parentheses are for
SSC-DC50AP/54AP/58AP
White balance AWB/5600K/ATW/ATWpro (switchable)
Automatic gain control (AGC) ON/OFF switchable
Power requirements
DC50A/50AP: DC 12 V
±
10%
DC 24 V
±
5 V (when YS- W150/
150P/ 250/250P is in use)
DC54A: AC 24 V (60 Hz)
DC54AP: AC 24 V (50 Hz)
DC58AP: AC 220 – 240 V (50 Hz)
Power consumption DC50A/50AP:4.5 W (DC 12V for power source)
5.5 W (when YS-W150/150P/
250/250P is in use)
DC54A/54AP: 6 W
DC58AP: 5.5 W
Operating temperature –10
°
C to +50
°
C (14
°
F to 122
°
F)
Operating humidity 20 to 80%
Storage temperature –40
°
C to +60
°
C (–40
°
F to 140
°
F)
Storage humidity 20 to 95%
Shock resistance 70 G
Mass DC50A(P)/DC54A(P): 600 g (1 lb 5 oz)
DC58AP: 900 g (1 lb 16 oz)
Dimensions DC50A(P)/DC54A(P): 64
×
57
×
137 (w/h/d) mm
(2 5 /8
×
2 1 /4
×
5 1 /2 inches)
DC58AP: 64
×
57
×
162 (w/h/d) mm
(2 5 /8
×
2 1 /4
×
6 1 /2 inches)
Supplied accessories 4-pin plug for auto iris lens (1)
Lens mount cap (1)
Operating Instructions (1)
Design and specifications are subject to change without notice.
G
H
H
I
J