Sony DVCAM DSR-PD150, Service Manual

Page: 265 / 279

— 3 —
Lens de
vice
Prism assy
(Including 3 CCD imagers)
V
AP unit
Mechanism deck EVF block
LCD902 (LCD panel)
LCD block
LCD901 (LCD panel)
LCD block
ND901 (Fluorescent tube)
LCD block
In
v
erter unit
Control switch
(CF-4980)
Mechanism deck M901 (Drum motor) Mechanism deck M902 (Capstan motor) FP-594 board
H902 (T reel FG sensor)
SE-108 board
SE600 to 603 (PITCH/Y
A
W
sensor)
PD-126 board
IC2101 (RGB dri
v
er (LCD))
PD-126 board
IC2103 (T
iming g
enera
tor (LCD))
LB-065 board
ND200 (Fluorescent tube (EVF))
VC-242 board
IC1802 (RGB dri
v
er (EVF))
VC-242 board
IC1803 (T
iming gener
a
tor (EVF))
VC-242 board
IC705, X701 (T
iming g
ener
a
tor)
VC-242 board
IC704 (S/H,
A
GC)
VC-242 board
IC706 (A/D con
verter)
VC-242 board
IC802 (Camera micro processor)
VC-242 board
IC1301 (LINE IN/OUT amp)
VC-242 board
IC301 (D
V signal process)
VC-242 board
IC101 (EQ,
A/D CONV
.,
PLL)
VC-242 board
IC102 (REC/PB amp)
VC-242 board
IC803 (EVR)
Replaced parts
Block replacement Parts replacement
z z z
z z
z z z z z
z z z z
z z z z z
z z z z
z z z z
Adjustment
Section
Camera
Adjustment
27MHz origin oscillation adj.
Zoom key center adj.
HALL adj.
Offset adj.
Flange back adj.
Pre-white balance data input
AWB standard data input
MAX GAIN adj.
LV standard data input
White balance ND filter 1 compensation
z z
z z
z
z
z
z
SECTION 5. ADJUSTMENTS
Page Before change After change
5-22
1-3. CAMERA SYSTEM ADJUSTMENTS
9. Pre White Balance Data Input
1-1. Adjusting items when replacing main parts and boards. (Refer to page 5-2)
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by
z
in the following table.
: Added portion.
: Changed portion.
: Deleted portion.
Table. 5-1-1(1).
Processing after Completing Adjustments
Order Page Address Data Procedure
3 0 01 00 Set the data.
4 Perform “Auto White Balance
Standard Data Input”.
Adjusting method:
Order Page Address Data Procedure
7 6 01 7F Set the data, and press PAUSE
button.
8 6 01 7D Set the data, and press PAUSE
button. (Note)
9 6 02 Check that the data changes to
“01”.
Adjusting method:
Order Page Address Data Procedure
7 F 16 Set the following data, and
press PAUSE button.
03 (NTSC), 83 (PAL)
8 6 01 7F Set the data, and press PAUSE
button.
9 6 01 7D Set the data, and press PAUSE
button. (Note)
10 6 02 Check that the data changes to
“01”.
Processing after Completing Adjustments
Order Page Address Data Procedure
3 F 16 Set the following data, and
press PAUSE button.
13 (NTSC), 93 (PAL)
4 0 01 00 Set the data.
5 Perform “Auto White Balance
Standard Data Input”.