17
EN
Writing Sub Codes
START ID ERASE
PHONES
REC MUTE
REC
AMS
MODE
RESET
RESET
ERASE
WRITE
REHEARSAL
RENUMBER
AUTO
MARGIN
OFF
REC
PLAY
TIMER
POWER
g
START ID
PHONE LEVEL
10
0
§
p
P
r
R
)
0
±
≠
·
OPEN/CLOSE
ANALOG
OPTICAL
COAXIAL
•
••
REC LEVEL
INPUT
48 kHz
44.1 kHz
LONG
•
••
••
REC MODE
STANDARD
SBM
ON
OFF
L
R
5
4
0
6
10
3
1
7
9
2
8
•
•
•
•
•
•
•
•
•
•
S
START ID
0 6
.
0 6
.
S
START ID
Accurate Positioning of Start IDs
(Rehearsal)
1
During playback, press START ID REHEARSAL
when you arrive at the proper position.
“REHRSL” appears, “START ID” flashes in the
display and Rehearsal repeats a 3-second portion
starting from the selected position. Note that the
repeated portion will play back 8 times, with the
remaining number of times appearing to the right
of the “REHRSL”. After 8 times, the deck
automatically stops.
2
Press
0
or
)
to move the beginning of the
repeated portion.
Each time you press the
0
or
)
button, the
beginning of the repeated portion shifts
backwards or forwards in 0.3-second increments,
up to a maximum extent of about 2 seconds (4
seconds in long-play mode) in either direction.
After pressing
0
twice
The time in the display shows the shift in position
from the time the START ID REHEARSAL button
was pressed.
3
Press START ID WRITE.
“ID WRITE” appears in the display for a few
seconds and the start ID is written on the tape at
the selected position. “START ID” flashes in the
display during this time.
After pressing
)
twice
Adjusting the Position of an
Existing Start ID
You can adjust the position of previously recorded
start IDs.
1
During playback, press START ID REHEARSAL
when the existing start ID you want to reposition
is displayed.
The deck rewinds to the beginning of start ID and
Rehearsal repeats a 3-second portion is displayed.
2
Do steps 1 to 3 of “Accurate Positioning of Start
IDs (Rehearsal)” on this page.
You can move the start ID to a maximum extent of
about 2 seconds (4 seconds in long-play mode) in
either direction from its original position.
Note
Start IDs written within 10 seconds from the end of the tape
may be difficult or impossible to move.
Erasing Start IDs
You can erase any start ID.
Press START ID ERASE when the start ID you want to
erase is displayed.
“(ERASE)” appears in the display as the deck rewinds
to the beginning of the start ID, then “ID ERASE”
appears as the deck erases the start ID.
• It takes 9 seconds to erase a start ID.
• Program numbers are erased together with start IDs.
Repeated portion
3 seconds
0.3 sec
0.3 sec
↓
Movement with each
press of
0
Position where the START
ID REHEARSAL button is
pressed in step 1.
Movement with each press of
)
START ID REHEARSAL
PHONES
REC MUTE
REC
AMS
MODE
RESET
RESET
ERASE
WRITE
REHEARSAL
RENUMBER
AUTO
MARGIN
OFF
REC
PLAY
TIMER
POWER
g
START ID
PHONE LEVEL
10
0
§
p
P
r
R
)
0
±
≠
·
OPEN/CLOSE
ANALOG
OPTICAL
COAXIAL
•
••
REC LEVEL
INPUT
48 kHz
44.1 kHz
LONG
•
••
••
REC MODE
STANDARD
SBM
ON
OFF
L
R
5
4
0
6
10
3
1
7
9
2
8
•
•
•
•
•
•
•
•
•
•
