DSX-MS60
31
Pin No.
Pin Name
I/O
Description
1
CYRIL_SEL
I
Cyrillic letter response setting terminal “H”: corresponds to Cyrillic letter
2
B-OUT_SEL
I
Blackout setting terminal “H”: blackout effective Fixed at “L” in this set
3
COL_SW
I
Setting terminal for the illumination color “L”: 2 colors, “H”: 1 color Not used
4
ILLUMI_SEL
I
Setting terminal for the illumination color “L”: 2 colors, “H”: 1 color Fixed at “H” in this set
5
DOOR SW
I
Front panel open/close detection signal input terminal “L”: front panel is closed
6
DOOR_IND
O
Sub Panel LED drive signal output terminal
7
NOSE_SW
I
Front panel remove/attach detection signal input terminal “L”: front panel is attached
8 to 10
NCO
-
Not used
11, 12
RE_IN0, RE_IN1
I
Jog dial pulse input from the rotary encoder
13
X_OUT
O
Sub system clock output terminal (32.768 kHz)
14
X_IN
I
Sub system clock input terminal (32.768 kHz)
15
VCC
-
Power supply terminal (+3.3V)
16
VSS
-
Ground terminal
17
C
-
Regulator stabilization capacity connecting pin
18
UNISI
I
SONY bus data input from the SONY bus interface
19
UNISO
O
SONY bus data output to the SONY bus interface
20
UNISCK
O
SONY bus clock signal output to the SONY bus interface
21
NCO
-
Not used
22
I2C_SIO
I/O
IIC two-way data bus
23
I2C_SCK
O
IIC data transfer clock signal output terminal
24
NCO
O
Not used
25
ACC_IN
I
Accessory power detection signal input terminal “L”: accessory power on
26
TEL_ATT
I
Telephone muting detection signal input terminal
At input of “H”, the audio signal is attenuated by 20 dB
27
ATT
O
Muting on/off control signal output terminal
28
BUS_ON
O
SONY bus on/off control signal output to the SONY bus interface “L”: bus on
29
SYS_RST
O
Reset signal output terminal
30
CD_ON
I
CD servo power supply control request input terminal
31
CDM_ON
I
CD mecha power supply control request input terminal
32
AVCC
-
Power supply terminal (+3.3V)
33
AVRH
I
Reference voltage (+3.3V) input terminal
34
RC_IN1
I
Rotary remote commander key input terminal
35
AVSS
-
Ground terminal
36
NCO
-
Not used
37
VSM
I
FM and AM signal-meter voltage detection signal input from the PLL
38
SA_IN
I
Spectrum analyzer display data select signal input terminal
39, 40
KEY_IN1, KEY_IN0
I
Front panel key input terminal
41
RC_IN0
I
Rotary remote commander key input terminal
42, 43
NCO
-
Not used
44
VSS
-
Ground terminal
45
KEY_ACK0
I
Acknowledge signal (wake up signal) input terminal for the rotary remote commander
On at input of “L”
46
KEY_ACK1
I
Acknowledge signal (wake up signal) input terminal for the front panel key On at input of “L”
47
NCO
O
Not used
48
LCD_CE
O
Chip enable signal output to the liquid crystal display driver
49
LCD_SO
O
Serial data output to the liquid crystal display driver
50
LCD_SCK
O
Serial data transfer clock signal output to the liquid crystal display driver
51 to 53
MD2, MD1, MD0
I
Operation mode setting terminal
54
RESET
I
System reset signal input from the reset signal generator and reset switch “L”: reset
55 to 57
AREA_SEL2 to
AREA_SEL0
I
Setting terminal for the destination
58
WAKE_UP
O
Wakeup signal output to the USB controller
59
MC_RX
I
Serial receive data input from the USB controller
60
MC_TX
O
Serial transmit data output to the USB controller
61
CLK
O
Not used
62
Z_MUTE
O
Not used
63
ILL_IN
I
Illuminate line detect signal input for the auto dimmer control
Dimmer is present at input of “L”
64
TEST
I
TEST Mode detect input terminal
MAIN BOARD IC501 MB90F058PF-G-120-NNE1 (SYSTEM CONTROLLER)
