Sony DDM-2800CSU Operating Instructions Manual Download Page 2

2

The model and serial numbers are located at the rear of the
unit. Record these numbers in the spaces provided below.
Refer to them whenever you call upon your Sony dealer
regarding this product.

Model No.

Serial No.

WARNING ........................................................................... 2
Features .............................................................................. 3
Precautions ......................................................................... 3
Location and Function of Controls ...................................... 4

Rear panel ..................................................................... 4

Specifications ...................................................................... 5

Table of Contents

Owner’s Record

English

WARNING

To prevent fire or shock hazard, do not
expose the unit to rain or moisture.

this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to
correct the interference at his own expense.

You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.

The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with
the limits for a digital device pursuant to Subpart B of Part
15 of FCC Rules.

NOTICE
This notice is applicable for USA/Canada only.
If shipped to USA/Canada, install only a UL LISTED/CSA
LABELED power supply cord meeting the following
specifications:
SPECIFICATIONS

Plug Type

Nema-Plug 5-15p

Cord

Type SVT or SJT, minimum 3 

×

 18,

AWG

Length

Maximum 15 feet

Rating

Minimum 7 A, 125 V

NOTICE
Cette notice s'applique aux Etats-Unis et au Canada
uniquement.
Si cet appareil est exporté aux Etats-Unis ou au Canada,
utiliser le cordon d'alimentation portant la mention UL
LISTED/CSA LABELED et remplissant les conditions
suivantes:
SPECIFICATIONS

Type de fiche Fiche Nema 5-15 broches
Cordon

Type SVT ou SJT, minimum 3 

×

 18

AWG

Longueur

Maximum 15 pieds

Tension

Minimum 7 A, 125 V

This symbol is intended to alert the
user to the presence of uninsulated
"dangerous voltage" within the
product's enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.

Thie symbol is intended to alert the
user to the presence of important
o p e r a t i n g   a n d   m a i n t e n a n c e
(servicing) instructions in the literature
accompanying the appliance.

For the customers in the USA
Warning-This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of

Summary of Contents for DDM-2800CSU















Reviews: