Sony CXD5602 User Manual Download Page 951

Page: 951 / 1010

CXD5602 User Manual

－

951/1010

－

3.14.3.6.2

The reset of each block can be controlled using the registers. Since the control flow varies according to the

function block, refer to each block’s Section. Table SYSIOP Clock and Reset Control-809 shows the reset control

registers.

Table SYSIOP Clock and Reset Control-769 Reset Control Registers

Address

Bit Field Name

Type

Bit

Initial

Value

Description

0x04100700

SWRESET_BUS

Reserved

[31:17]

Reserved

XRST_PMU_I2C

[16]

Indicated as RST(9) in

Figure SYSIOP

Clock and Reset Control-117

Reset for I2C4

0 Reset is performed

1: Reset release

Reserved

[15:12]

Reserved

XRST_I2CM_SU

[11]

Indicated as RST(8) in

Figure SYSIOP

Clock and Reset Control-117

Reset for I2C2

XRST_UART0

[10]

Indicated as RST(7) in

Figure SYSIOP

Clock and Reset Control-117

Reset for UART0

XRST_HOSTIFC

_ISOP

[9]

Indicated as RST(6) in

Figure SYSIOP

Clock and Reset Control-117

Reset for HOSTIFC Sequencer

XRST_HOSTIFC

[8]

Indicated as RST(5) in

Figure SYSIOP

Clock and Reset Control-117

Reset for HOSTIFC

Reserved

[7:6]

Reserved

XRST_UART1

[5]

Indicated as RST(3) in

Figure SYSIOP

Clock and Reset Control-117

Reset for UART1

Reserved

[4:3]

Reserved

XRST_SAKE

[2]

Indicated as RST(2) in

Figure SYSIOP

Clock and Reset Control-117

Reset for Crypto(Clefia)

Summary of Contents for CXD5602



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CXD5602

Reviews:

Related manuals for CXD5602

Brands by name

Popular brands

Sony CXD5602, User Manual

Search results

Summary of Contents for CXD5602

Reviews:

Related manuals for CXD5602

Brands by name

Popular brands