background image

1

Model Name Using Similar Mechanism

NEW

CD Drive Mechanism Type

MG-383V-121//K

Optical Pick-up Name

KSS-720A

SERVICE MANUAL

US Model

Canadian Model

CDX-M750

AEP Model

UK Model

CDX-M700R

CDX-M700R/M750

Photo: CDX-M750

• The tuner and CD sections have no adjustments.

AUDIO POWER SPECIFICATIONS (CDX-M750)

POWER OUTPUT AND TOTAL HARMONIC DISTORTION
19 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 1% total harmonic distortion.

Other Specifications
CD player section

System

Compact disc digital audio
system

Signal-to-noise ratio

90 dB

Frequency response

10 – 20,000 Hz

Wow and flutter

Below measurable limit

Laser Diode Properties (CDX-M750)

Material

GaAlAs

Wavelength

780 nm

Emission Duration

Continuous

Laser output power

Less than 44.6 µW*

This output is the value measured at a distance

of 200 mm from the objective lens surface on the
Optical Pick-up Block.

Tuner section

FM

Tuning range

87.5 – 107.9 MHz (CDX-M750)
87.5 – 108.0 MHz (CDX-M700R)

Antenna terminal

External antenna connector

Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity

8 dBf

Selectivity

75 dB at 400 kHz

Signal-to-noise ratio

66 dB (stereo),
72 dB (mono)

Harmonic distortion at 1 kHz

0.6% (stereo),
0.3% (mono)

Separation

35 dB at 1 kHz

Frequency response

30 – 15,000 Hz

AM (CDX-M750)

Tuning range

530 – 1,710 kHz

Antenna terminal

External antenna connector

Intermediate frequency 10.7 MHz/450 kHz
Sensitivity

30 µV

SPECIFICATIONS

MW/LW (CDX-M700R)

Tuning range

MW: 531 – 1,602 kHz
LW: 153 – 279 kHz

Aerial terminal

External aerial connector

Intermediate frequency 10.7 MHz/450 kHz
Sensitivity

MW: 30 µV
LW: 40 µV

Power amplifier section

Outputs

Speaker outputs

Speaker impedance

4 – 8 ohms

Maximum power output 50 W 

×

 4 (at 4 ohms)

General

Outputs

Audio outputs (3)
Power antenna relay
control lead (CDX-M750)
Power aerial relay
control lead (CDX-M700R)
Power amplifier control
lead

Inputs

Telephone ATT control
lead
Illumination control lead

Power requirements

12 V DC car battery
(negative ground)

FM/AM COMPACT DISC PLAYER

CDX-M750

FM/MW/LW COMPACT DISC PLAYER

CDX-M700R

– Continued on next page –

Ver 1.2  2001. 03

Sony Corporation

Audio Entertainment Group

General Engineering Dept.

9-870-134-12

2001C0400-1

© 2001. 3

Summary of Contents for CDX-M700R



















































































Reviews: