Sony CDX-C4840R, Service Manual

Page: 23 / 56

Pin No. Pin Name I/O Pin Description
56 AMP ON O Power amplifier power control output
57 TXT ON O Reset output to CD-TEXT decoder IC.
58 VOL ATT O Electric volume mute control output
59 NIL — Not used. (Open)
60 ATT O System attenuate control output
61 RC IN1 I Rotary commander shift key input 1
62 TU ATT O Tuner attenuate output
63 VSS — Ground
64 NIL — Not used. (Open)
65 SSTOP I IF counter result signal detection input of PLL.
66 TEST I Test mode initial setting detection input
67 DAVN I RDS IC data acquisition detection input
68 FM ON/AM ON O FM ON output
69 TU ON O Tuner power control output
70 SDA I/O I
2
C BUS serial data input/output
71 SCL O I 2 C BUS serial clock output
72 NOSE2 I Front panel OPEN detection input
73 X1A O Sub ceramic oscillator output (32 kHz)
74 X0A I Sub ceramic oscillator input (32 kHz)
75 SCOR I SCOR signal detection input
76 BU IN I Backup power detection input
77 DQSY I CD-TEXT data setting completion signal detection input
78 CD SENS I CD SENS signal detection input
79 NIL I Key input acknowledge
80 TEL ATT I Telephone attenuate detection input
81 ST/MONO I/O Tuner stereo signal detection input/forced monaural output
82 SEEKOUT O SEEK output
83 SD IN I Signal detector input
84 WIDE O WIDE select output (Not used in this set.)
85 NARROW O NARROW select output (Not used in this set.)
86 HSTX — Hardware standby input (Connect to pin (º (RESET).)
87 MD2 — Operation mode input (Connect to ground in this set.)
88, 89 MD1, 0 — Operation mode input (Connect to VCC in this set.)
90 RESET I Reset input
91 VSS — Ground
92 X0 I Main ceramic oscillator input (4.19 MHz)
93 X1 O Main ceramic oscillator output (4.19 MHz)
94 VCC — Power supply pin (+5 V)
95 COM8V ON O COM 8V control output
96 NIL — Not used. (Open)
97 AREA1 I Destination select input 1 (Fixed at “L” in this set.)
98 AREA2 I
Destination select input 2 (Fixed at “L” (AEP, UK model) or “H” (German model)
in this set.)
99 LOUD I Fixed at “L” in this set.
100 BAND I Fixed at “H” in this set.
101 ACC IN I Accessory power detection input
102, 103 PH3, 2 I Disc insertion detection photo sensor input (Fixed at “H” in this set.)
104 LCD CE O LCD chip enable output
105 FLS W I Flash write input (Fixed at “H” in this set.)
106, 107 RE IN0, 1 I Rotary encoder input
108 ILL ON O Illumination power control output
109 PW ON O System power control output
110 NIL — Not used. (Open)
Pin No. Pin Name I/O Pin Description
111 ANT REM O ANT REMOTE power control output
112 NIL — Not used. (Open)
113 CTL2 — Not used in this set.
114 CD LD O Loading motor control output (Loading direction)
115 CD EJ O Loading motor control output (Eject direction)
116 L SW I Sled limit switch detection input
117 IN SW/(PH1) I Disc insertion detection input
118 D SW I DOWN switch detection input
119 VSS — Ground
120 SELF SW/(IN SW) I Disc self store detection input
– 23 – – 24 –
w w w . x i a o y u 1 6 3 . c o m
Q Q 3 7 6 3 1 5 1 5 0
9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL 13942296513 QQ 376315150 892498299 TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com