background image

2

• AC power cord must be changed only

at the qualified service shop.

On placement

• Place the player in a location with

adequate ventilation to prevent heat
build-up in the player.

• Do not place the player on a soft

surface such as a rug that might block
the ventilation holes on the bottom.

• Do not place the player in a location

near heat sources, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.

On operation

• If the player is brought directly from a

cold to a warm location, or is placed in
a very damp room, moisture may
condense on the lenses inside the
player. Should this occur, the player
may not operate properly. In this case,
remove the disc and leave the player
turned on for about an hour until the
moisture evaporates.

On adjusting volume

• Do not turn up the volume while

listening to a portion with very low
level inputs or no audio signals. If you
do, the speakers may be damaged
when a peak level portion is played.

On cleaning

• Clean the cabinet, panel and controls

with a soft cloth slightly moistened
with a mild detergent solution. Do not
use any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine.

If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.

WARNING

To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to
qualified personnel only.

– Reorient or relocate the receiving

antenna.

– Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet

on a circuit different from that to
which the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or
modification not expressly approved in
this manual could void your authority to
operate this equipment.

Owner’s Record

The model and serial numbers are
located at the rear of the unit.
Record the serial number in the space
provided below. Refer to them whenever
you call upon your Sony dealer
regarding this product.

Model No. _________________________

Serial No.

_________________________

This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.

This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.

INFORMATION

This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or
television reception, which can be
determined by turning the equipment off
and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:

Precautions

On safety

• Caution — The use of optical

instruments with this product will
increase eye hazard.

• Should any solid object or liquid fall

into the cabinet, unplug the player and
have it checked by qualified personnel
before operating it any further.

On power sources

• Before operating the player, check that

the operating voltage of the player is
identical with your local power
supply. The operating voltage is
indicated on the nameplate at the rear
of the player.

• The player is not disconnected from

the AC power source (mains) as long
as it is connected to the wall outlet,
even if the player itself has been
turned off.

• If you are not going to use the player

for a long time, be sure to disconnect
the player from the wall outlet. To
disconnect the AC power cord (mains
lead), grasp the plug itself;  never pull
the cord.

Summary of Contents for CDP-XE400 - Compact Disc Player

















Reviews: