Sony Ericsson W950c Working Instruction, Mechanical Download

Page: 43 / 56

Working Instruction

Mechanical

3/000 21-1/FEA 209 544/111 A

Sony Ericsson Mobile Communications AB

43(56)

3.24 Label

Follow the 2.1.2 Disassembly instructions!

•

Read the old label and/or write the information into the

“Label make” program before removal

•

Note the position of the label before removal

•

Heat up the label by using hot air, if needed.

•

Carefully remove the label without causing scratches

•

If there still are residues, clean the surface with isopropyl

alcohol

•

Check that the proper label format is loaded in the Zebra

printer.

•

Write a new label by using the program “Label make”

and check that the printing is OK.

•

Take the new label and place it onto the

frame

as in the

adjacent picture.

•

NE LABEL ONLY IS ALLOWED

Follow the 4.1.9 Reassembly instructions!

Summary of Contents for W950c

























































Search results

Summary of Contents for W950c

Reviews:

Related manuals for W950c

Brands by name

Popular brands

Sony Ericsson W950c, Working Instruction, Mechanical

Search results

Summary of Contents for W950c

Reviews:

Related manuals for W950c

Brands by name

Popular brands