manualshive.com logo in svg

Sonifex Redbox RB-DSD8, User Handbook Manual

Share
Download
Sonifex Redbox RB-DSD8 User Handbook Manual Download Page 35

Redbox RB-DSD8 User Handbook

23

connected via ethernet. If the unit fails to connect via DHCP, it will connect via a static 
address instead. Please note that the DHCP connection attempts will abort after 45 
seconds if unsuccessful. While connecting, the IP address, subnet mask and default 
gateway will all read 0. 0. 0. 0. if read serially.

IP Address

 - Displays the current IP address of the unit. If DHCP is enabled then this will 

normally be the IP address supplied by the DHCP server.

Subnet Mask

 - Displays the current subnet mask for the unit.

Default Gateway

 - Displays the current default gateway for the unit.

MAC Address

 - The unit’s MAC address. This cannot be changed.

Change Static Address

 - This allows you to alter the static address stored in the unit. This 

is the address that is used when DHCP is disabled or a DHCP server is not found. Selecting 
this button allows you to enter your own IP, subnet and gateway addresses in the edit 
boxes.

NB. The units are discovered using broadcast packets. If your PC has two network 
cards, then there is a limitation in windows that requires the two addresses to be on 
different subnet addresses.

Updating The Firmware

The RB-DSD8 firmware will at times be updated to add new features, or to correct any 
possible issues that may arise. 

Check for updates at: http://www.sonifex.co.uk/technical/software/

Firmware updates can be conducted through either Serial/Ethernet port. To update the 
firmware, click on the button labelled “Update Firmware” and then select the downloaded 
firmware file. Firmware files for the RB-DSD8 always have an “.ldr” extension. A progress bar 
will appear in SCi, indicating how much of the file has been uploaded to the unit.  When 
the unit switches to update mode, the front panel display LEDs will all be extinguished. The 
switch mode buttons are then used to display the status of the upload:

Uploading the Code:

 The SLAVE button will begin to flash amber to confirm the unit is 

receiving the new firmware to RAM.

Copying Code To Flash Memory: 

The SLAVE button will be solid amber while the unit 

checks the integrity of the file and copies the file from RAM to flash memory.

Successful Update: 

The AUTO button will be solid green for two seconds and the unit will 

automatically reset and begin running the new code.

Unsuccessful Update: 

The MANUAL button will be solid red for two seconds and the unit 

will return to running the last code used.

SCI FOR RB

-DSD8

6

SCI FOR RB-DSD8

Summary of Contents for Redbox RB-DSD8









































Reviews:

No comments

Brands by name

Popular brands

Load more brands