6
SONANCE CINEMA
®
SELECT
6. Tighten the four screws on the front of the speaker baffle. The RotoLock clamps will automatically
rotate into position and begin clamping the speaker (Figure 11).
• When you notice resistance on the screws the speaker has been clamped successfully.
IMPORTANT: Always use low-torque settings; NEVER over-tighten.
N
OTE
: T
HE SPEAKER FLANGE IS DESIGNED TO FLEX AND CONFORM TO ANY SMALL IMPERFEC
-
TIONS IN THE WALL SURFACE
. D
O NOT TIGHTEN THE SCREWS SO MUCH SO THAT THE FLANGE
BOWS
-
OUT
.
7. Attach the grille after the speaker has been installed. Insert about half of the grille into the groove
at the edge of the speaker. Gently fit the remaining half of the grille by working around the speak-
er, fitting the grille into the groove as you go.
N
OTE
: Y
OU CAN ADJUST THE TORQUE APPLIED TO THE
R
OTO
L
OCK SCREWS TO ACHIEVE A PROP
-
ER GRILLE FIT
.
PAINTING THE SPEAKERS AND GRILLES
You can paint the speakers and grilles before installing them, which will eliminate the “paint scar” that
can be left on the wall if the speaker ever needs to be removed for service. You can also paint the
speakers after installation, but before the grilles are attached. All Sonance Symphony speakers come from
the factory fitted with a plastic ‘paint plug’ that protects the speaker drivers while the mounting flange
is being painted.
Sonance always suggests painting the grille separately from the speaker. Before painting, carefully remove the under-grille cloth. It is held in place with a
light tacking glue that makes it easy to remove.
Spray the grille with thinned paint (5 parts thinner to 1 part paint), being careful not to plug the holes. Too heavy a coat of paint on the grille will
adversely affect the sound of the speaker.
Once the grille and flange are painted and dry, replace the under-grille cloth, remove the paint plug from the mounting flange and install the grille.
SPECIFICATIONS
RotoLock
®
Clamps
F i g u r e 1 1 :
T i g h t e n i n g t h e R o t o L o c k C l a m p s
Cinema Select LCR
Tweeter:
1" (25mm) Silk dome, Ferrofluid-cooled,
shielded magnet
Woofer:
6½" (165mm) Carbon fiber cone, rubber
surround, shielded magnet
Frequency Response:
80Hz – 20kHz ±3dB
Impedance:
8 Ohms nominal; 5 Ohms minimum
Power Handling:
5 watts minimum; 135 Watts maximum
Sensitivity:
90dB SPL (2.83V 1 meter)
Grille Material:
Perforated aluminum
Adjustments:
None
Dimensions (W x H x D):
8¼” x 12
3
/
16
" x 3
7
/
8
"
(210mm x 310mm x 98mm)
Cutout Dim. (W x H):
6
13
/
16
" x 10
11
/
16
" (172mm x 270mm)
Shipping Weight:
5 lbs. (2.3kg) Each
Cinema Select SUR
Tweeter:
Two 1" (25mm) silk domes, Ferrofluid-cooled
Woofer:
6½" (165mm) Carbon fiber cone, rubber
surround
Frequency Response:
55Hz – 20kHz ± 3dB
Impedance:
8 Ohms nominal; 5 Ohms minimum
Power Handling:
5 watts minimum; 135 Watts maximum
Sensitivity:
90dB SPL (2.83V 1 meter)
Grille Material:
Perforated aluminum
Adjustments:
None
Dimensions (W x H x D):
8¼” x 12
3
/
16
" x 3
7
/
8
"
(210mm x 310mm x 98mm)
Cutout Dim. (W x H):
6
13
/
16
" x 10
11
/
16
" (172mm x 270mm)
Shipping Weight:
10 lbs. (4.5kg) Pair
