Sommerkamp TS-712P Instruction Manual Download Page 4

GENERAL  DESCRIPTION

Your  SOMMERKAMP  TS-712P  transceiver  has  been  designed  for  continous  heavy 

duty  base  station  application.  It  сап  be  operated  with  a  microphone  and  internai 

speaker  or  headset,  speaker/microphone  combination,  teiephoneset  incorporating 

automatic  voice  operated  transm it/receive  switching,  external  sélective  calling 

with  automatic  answerback  and  many  more.

GENERAL:

The  transceiver  is  desïgned  to  operate  from  110/220  Volt  AC  as  a  base  station. 

Its  straight  forward  12  channel  capability  allows  it  to  operate  on  any  combination 

of  frequencies  within  26.5  and  29.7  MHz  by  inserting  the  corresponding  xtals  and 

retuning  the  transceiver  if  required.  The  Xtals  in  the  transceiver  are  standard  27 

MHz  CB  Xtals  with  plus  or  minus  455  KHz  receiver  offset.  No  special  synthesiser 

or  IF  Xtals  are  required.

RECEIVER  SECTION

The  receiver  section  is  designed  to  receive  amplitude  modulated  (AM/A3)  signais 

in  the  27  MHz  (11  meter)  citizens  band.  The  unique  combination  of  low  noise 

Field  E ffect  Transistors  (FET),  single  conversion,  a  combination  of  mechanical 

ceramic,  and  L/C  filte rs ,  fui ly  automatic  noise  lim ite r  and  a  hi fi  quality  speaker 

am plifier  w ill  give  you  exceptional  réception  quality  in  this  fine  piece  of 

equipment.

In  addition,  the  above  combination  of  the  latest  technology  provides  you  with 

a  sensitivity  and  unwanted  signal  rejection  and  noise  suppression  available 

previously  only  in  space  and  m ilita ry  communication  equipment.

The  power  supply  of  the  receiver  RF.  IF  and  oscillator  section  is  stabilized  by  an 

extreme  Sharp  c u t-o ff  Zener  diode  to  obtain  the  high  sensitivity  and  unwanted 

signal  rejection.  The  fui ly  automatic  sériés  gâte  noise  lim iter,  which  virtually 

cuts  o ff  the  audio  output  during  ignition  noise  puises,  is  defeatable  to  make 

even  the  weakest  signal  audible  which  otherwise  would  be  eut  off  by  the  threshold 

level  of  the  ANL  switching  diode.

The  high  squelch  sensitivity  is  achieved  by  using  a  seperate  squelch  detector  and 

switching  circuit  with  a  carefully  balanced  hystérésis.  The  transformerless  hifi 

quality  audio  power  am plifier  w ill  drive  any  load  between  8  ohms  and  indefininite 

such  as  internai  speaker  or  external  speaker/microphone  or  headset  combinations 

having  the  above  impédances.

The  meter  indicates  the  field  strength  during  réception  of  a  signal.

3

Summary of Contents for TS-712P
















Reviews: