We reserve the right to make changes due to technical improvements.
CENTRALIS uno RTS VB
2
GROUP CONTROL (one transmitter for several receivers)
To program one control in several
CENTRALIS uno RTS VB
, set all the receivers in their programming mode then repeat the same procedure.
It is recommended not to use a RT control as a general control point.
To record several RTS controls in CENTRALIS uno RTS VB, repeat the same procedure as described in section 3.1 for each control.
You can also use an already recorded control to set the
CENTRALIS uno RTS VB
in its programming mode
RTS control :
press for more than 2 sec. on the “prog” button.
RT control :
remove the battery, press briefly the button, replace the battery and press for more than 2 sec. on the button.
➜
The LED of the
CENTRALIS uno RTS VB
lights on and the blind jogs briefly UP and DOWN indicating that the
CENTRALIS uno RTS VB
is in programming mode and that you can record a new control.
You can program up to 12 controls to one receiver. If you try to enter a 13th, your instruction will be ignored.
CENTRALIS uno RTS
can be operated by its push-buttons or with a RT/RTS control.
CENTRALIS uno RTS VB
offers two different modes to control the venetian blind.
P
R
O
G
MAINS
230V - 50Hz
3 wires x 1,5 mm
2
4 wires x 0,75 mm
2
Neutral
Earth
Phase
1 2 3 4 5 6
5 wires x 1,5 mm
2
N
L
N
Centralis uno RTS
Junction box
Motor
Supply
Phase
Neutral
Earth
Earth
(green/yellow)
Common
(blue)
Up
(black or brown)
Down
(black or brown)
L
➜
N
➜
N
▲
▼
1
2
3
4
5
6
N
L
N
SUPPLY
230V 50Hz
Phase
Neutral
Earth
LT motor
DOWN
PE
N
UP
• disconnect mains before carrying out any work.
• ensure that no forces act on the screw terminals after installation.
3
Radio programming
Set the
CENTRALIS uno RTS VB
in
its programming mode by pressing the
PROG button until the blind jogs briefly
(UP/DOWN).
The
CENTRALIS uno RTS VB
will
remain ready to record a control for two
minutes.
P
R
O
G
➜
2 sec.
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
3V
LITHIUM
RENA
TA
CR 2032
3V
LITHIUM
RENA
TA
CR 2032
S
W
IS
S
M ADE
0,5 s
0,5 s
0,5 s
We reserve the right to make changes due to technical improvements.
3
CENTRALIS uno RTS VB
Press the prog button of the
CENTRALIS uno RTS VB
to enter in programming mode, then press shortly the prog button of the RTS
control you wish to remove.
It is also possible to set the
CENTRALIS uno RTS VB
in its programming mode with another RTS control (see 3.2), then press
shortly the prog button of the RTS control you wish to remove.
To remove all the controls, do a complete reset of the
CENTRALIS uno RTS VB
(see section 5).
4
Operating
“auto” position :
All commands from the push buttons of the
CENTRALIS uno RTS VB
(local control) and from the radio
controls (master control) are taken into account.
“0” position :
Only the push button commands are taken into account and the radio commands are disabled (This feature
allows to isolate a room from the master control). To force the control of the CENTRALIS uno RTS VB with
radio, the radio command should be longer than 2 sec.
In association with the
SOLIRIS/EOLIS sensors RTS
or a
CHRONIS RTS light
,
CENTRALIS uno RTS VB
is able to control and protect the blind according to the sun
and wind conditions.
To record a
SOLIRIS/EOLIS RTS
sensor or a
CHRONIS RTS light
in the
CENTRA-
LIS uno RTS VB
, repeat the same procedure as describe in section 3.2 (record a new
control).
Refer to the instruction manual of the relevant products for the programming and set-
ting procedures.
➜
The blind jogs briefly (UP/DOWN)
and the LED of the
CENTRALIS
uno RTS VB
blinks during 5 secs.
indicating that the control has been
recorded.
CENTRALIS uno RTS VB
quits its
programming mode.
RTS control
Press briefly the program-
ming button on the RTS
control you wish to record.
RT control
Remove the battery, press
briefly the button, replace the
battery and press again briefly
the button.
UP/DOWN/STOP/TILT commands
4.1
0/auto switch
4.2
Wind/Sun/Light functions
4.3
Remove a control (on an existing installation)
3.3
Initial installation : record the first control
3.1
Record new controls
3.2
Wiring
2.2
US mode (factory mode)
§
Press briefly the
▼
or
▲
buttons to raise or lower the blind.
§
Press briefly the
■
button To stop the blind.
§
To tilt the slats, press and hold the
▼
or
▲
buttons.
If you hold the control buttons for more than 6 seconds, the blind
will start to move continuously up to its end limits.
EU mode :
§
To raise or lower the blind, press and hold more than 2 secs. the
▼
or
▲
buttons.
§
To stop the blind, press briefly the
■
button.
§
To tilt the slats, press briefly the
▼
or
▲
buttons.
UP button
0/auto switch
STOP/IP button
DOWN button
The configuration can be changed by pressing for more than 5 secs. on the
■
button of a RTS control just after the power on. The
blind jogs, indicating that
CENTRALIS uno RTS VB
has changed the configuration.
With the
CENTRALIS uno RTS VB
, it is possible to program an automatic intermediate position (IP) and an automatic tilting of the
slats. You can choose to program one or the other, or both. The recording of the intermediate position and the tilting can be made
from the
CENTRALIS uno RTS VB
or from a RTS control.
Intermediate position / automatic slat tilting
4.4
1
2
