Solwise WL-STATION-N2 User Manual Download Page 31 | Manualshive

Page: 31 / 39

background image

31

◆

Server IP

— Sets the L2TP server IP Address. (Default: l2tp_server)

◆

User Name

— Sets the L2TP user name for the WAN port.

◆

Password

— Sets a L2TP password for the WAN port.

◆

Address Mode

— Sets a L2TP network mode. (Default: Dynamic IP)

◆

Operation Mode

—

Enables and configures the keep alive time.

◆

Primary DNS Server

— The IP address of the Primary Domain Name Server. A DNS

maps numerical IP addresses to domain names and can be used to identify network
hosts by familiar names instead of the IP addresses. To specify a DNS server, type
the IP addresses in the text field provided. Otherwise, leave the text field blank.

◆

Secondary DNS Server

— The IP address of the Secondary Domain Name Server.

LAN

In this section, the LAN settings are configured based on the IP Address and Subnet
Mask. The IP address is also used to access this Web-based management interface.
It is recommended to use the default settings if you do not have an existing
network.

◆

IP Address

— The IP address of OUTDOOR AP/CPE on the local area network.

( Default: 192.168.2.1 )

«
...
29
30
31
32
33
...
»

Summary of Contents for WL-STATION-N2








































Reviews:

No comments

Related manuals for WL-STATION-N2

3CRWE51196 - OfficeConnect Wireless Cable/DSL...

Brand: 3Com Pages: 6

Brand: Ubiquiti Pages: 32

AR 18-3XE/18-21X Series

Brand: H3C Pages: 79

Brand: Airlink101 Pages: 7

EWP-WA6630X-JP-FIT

Brand: H3C Pages: 34

Brand: Pakedge Pages: 62

Brand: Arista Pages: 4

Wireless LAN Access Point

Brand: Kobian Pages: 35

SCALANCE W734-1

Brand: Siemens Pages: 64

Brand: Jaton Pages: 8

Brand: Hills Pages: 12

Brand: EnGenius Pages: 4

Brand: EnGenius Pages: 5

Brand: Credo mobile Pages: 6

Brand: ELTEX Pages: 78

Brand: Ebyte Pages: 31

Brand: Ebyte Pages: 37

Brand: Ubiquiti Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands