9
CONNECT THE WATER SUPPLY HOES PIPE
WARNING:
•
To prevent leakage or water damage, follow the
instructions in this chapter
•
Do not kink, crush, modify or sever the water inlet hose!
Connect the water supply hose to the water inlet valve and
a water tap with cold water as indicated.
Note: Connect manually, do not use tools.
Check if the connections are tight.
POSITION THE DRAIN HOSE
The outlet hose (used to drain the discharged water) is to
be ideally connected to the relevant waste pipe, although
it can also be positioned to drain into a sink/trough.
Note that the outlet hose has a minimum outlet
position of 60cm and a maximum position of 100cm
(as illustrated below).
WARNING:
•
If you are positioning the outlet hose to drain into a
sink or trough, please ensure that it is fixed in place
and that the sink remains unblocked at all times.
•
If drain hose is too long, do not force it into washing
machine as it will cause abnormal noises.
APPLYING THE ACOUSTIC SPONGE
Note: Please make sure to assemble the acoustic sponges,
which can effectively reduce the noise caused by
the machine while working, in order to provide you
with a more peaceful and quiet living environment.
1. Lie the machine laid on the floor, using some soft
material like foam or clothes between the machine
and floor for protection;
2. Stick the 2× longer sponges to the longer bottom
edges of machine, and the 2× shorter sponges to the
shorter bottom edges.
Warning!
Drain Hose
There are two ways to place the end of drain hose:
1.Put it into the water trough.
2.Connect it to the branch drain pipe of
the trough.
•
• If drain hose is too long, do not force it into washing machine as it will cause
abnormal noises.
When installing drain hose, fix it properly with a rope.
•
• Position drain hose properly ,otherwise damage might result of water leakage.
Do not
kink or protract the drain hose.
Water
trough
M
in
.
60
cm
10
0c
m
M
ax
.
Warning!
INSTALLATION
water supply hose
water Inlet valve
Connect the other end of inlet pipe to the inlet valve at the backside of product
and fasten the pipe tightly clockwise.
11
Warning!
Drain Hose
There are two ways to place the end of drain hose:
1.Put it into the water trough.
2.Connect it to the branch drain pipe of
the trough.
•
• If drain hose is too long, do not force it into washing machine as it will cause
abnormal noises.
When installing drain hose, fix it properly with a rope.
•
• Position drain hose properly ,otherwise damage might result of water leakage.
Do not
kink or protract the drain hose.
Water
trough
M
in
.
60
cm
10
0c
m
M
ax
.
Warning!
INSTALLATION
water supply hose
water Inlet valve
Connect the other end of inlet pipe to the inlet valve at the backside of product
and fasten the pipe tightly clockwise.
11
9
9
INSTALLATION
Remove transport bolts
• You must remove the transport bolts from the backside before using the product.
Warning!
！
Loosen the 4
transport bolts with
a spanner.
Remove the bolts
including the rubber
parts and keep them
for future use.
Close the holes
using the cover caps.
Levelling the washing machine
• The
lock nuts
on all four feet must
be
screwed tightly
against
the
housing.
Warning!
！
1. Loosen the lock nut.
2. Turn the foot until it reaches the floor.
3. Adjust the legs and lock the nuts with a
spanner. Make sure the machine is level
and
steady.
Connect the water supply hose
To prevent leakage or water damage, follow the instructions in this chapter
• Do not kink, crush or modify water inlet hose.
Warning!
！
！
Connect the water supply
hose to the water inlet valve
and a water tap with cold
water as indicated.
• Connect manually, do not use tools. Check if the connections are tight.
Note!
9
9
INSTALLATION
Remove transport bolts
• You must remove the transport bolts from the backside before using the product.
Warning!
！
Loosen the 4
transport bolts with
a spanner.
Remove the bolts
including the rubber
parts and keep them
for future use.
Close the holes
using the cover caps.
Levelling the washing machine
• The
lock nuts
on all four feet must
be
screwed tightly
against
the
housing.
Warning!
！
1. Loosen the lock nut.
2. Turn the foot until it reaches the floor.
3. Adjust the legs and lock the nuts with a
spanner. Make sure the machine is level
and
steady.
Connect the water supply hose
To prevent leakage or water damage, follow the instructions in this chapter
• Do not kink, crush or modify water inlet hose.
Warning!
！
！
Connect the water supply
hose to the water inlet valve
and a water tap with cold
water as indicated.
• Connect manually, do not use tools. Check if the connections are tight.
Note!
10
10
INSTALLATION
Drain Hose
There are two ways to place the end of drain hose:
1.Put it into the water trough.
2.Connect it to the branch drain pipe of
the trough.
•
• Position drain hose properly ,otherwise damage might result of water leakage.
Do not
kink or protract the drain hose.
Water
trough
10
0c
m
M
ax
.
Warning!
！
！
Warning!
！
M
in
.
60
cm
• Please make sure to assemble the acoustic sponges, which can effectively
reduce the noise caused by the machine while working, in order to provide
you with a more peaceful and quiet living environment.
Note!
Acoustic Sponge
2x
2x
1. Get the machine laid on the floor, using some soft material like foam or clothes
between the machine and floor for a protection;
2. Stick the 2x longer sponges to the longer bottom edges of machine, and the 2x
shorter sponges to the shorter bottom edges.