Solotech Solo C330 User Manual Download Page 11

Page: 11 / 16

1.6 WiFi Reconfigure

When your network changes, you can recofigure WiFi as shown below:
1.6.1 Please turn on the camera and wait for the WiFi indicator light comes on
1.6.2 Then press the reset key and hold for 3-5 seconds untill the WiFi indicator
flickering blue light comes on.
1.6.3 Add equipment by APP again(see Fig.1.4.2).

1.5.2 Menu bar
Camera: Capture a screenshot of the live video feed and save it to the
smartphone album.
Audio: Turn on audio to receive sound from the camera’s location.
Turn on Microphone to speak to the camera.
Full screen: View the live video feed in landscape mode.
Protection: After selecting “motion detection” function, when cameras is
triggered, the alarm system will catch picture and send message to your app.
Protection Mode includes: motion detection(on/off), sensitivity(PIR sensitivity,
select low, middle, or high).

Playback: to view the video saved in SD card.
Share: Share video with friends and relatives who have registered an
account with Doby. After entering their account and then adding them to
share the video, then they can also view the video.(C330 does not support
viewing by multiple users at the same time. Only one user can view at any

moment)

Product dimensions

2.4 Notes:

PIR sensor is a high-sensitivity detector which is used for infrared detection of
object motion. However, motion detection can be triggered by the change of
background lighting change, passing by vehicles or the blowing leaves.

(Dimension:mm)

Notice

Technical parameters

Items Specifications

Product model Battery Mobile WiFi Camera

ens 2.1mm/110°

Video H.264 encoding
Audio frequency

√

WiFi Support IEE802.11b/g/n protocol(2.4GHz)
Infrared LEDs

√

PIR motion detection PIR range ≈

15 Feet (5 Meters)

If there is no operation within 30 seconds after last
trigger

, c

amera enter the sleep state

Charging source Mini USB interface 5V 1A
Dimensions 4.7 X 3.3 X 2.9 inch (84X74X118.7mm)
Expandable storage space Maximum support 32GB Micro SD card
Weight 0.3 lb (153g

)

1500mAh, can be waked up or triggered (1 minute
Battery and standby per time) more than 10-20 times daily. The battery
can be on standby for more than 1 month.

Cycle time

1.5.4 PIR detection

• If an object moves within 5 meters in front of the camera, motion detection

will be triggered.

• Alarm message will be sent through push notification on the client app.

• Screenshot / live video feed / playback video will be sent.

2 Installation

Illustration

2.1 Before installing the camera, please confirm steady WiFi signals at the

location of camera installation (at least two grids of WiFi signals) . If the signal
is not strong enough, you may install a WiFi repeater to extend the WiFi coverage.

2.2 Avoid areas with moving objects that may disturb the camera.
2.3 The bracket interface is standard 1/4’’ which can be replaced easily.
It’s not appropriate to install the equipment next to air conditioner,
windows, or other places where the temperature fluctuates drastically.

Camera

Router

Repeater

The sticker is applies to the wall mount.

If the camera detects false alarm frequently

，

please use

“PIR shield sheet” to reduce motion detection area. If this
does not resolve the issue, you have option to turn off the
motion detection function by selecting "security" option in
Notice APP under Protection menu.

Put the sticker to bottom of

camera's bracket, and then stick the camera on the wall.

56mm

84mm

74mm

26mm

118

.7m

.5m

Common problems and solutions

1 What do I do when I get error message while adding camera?

There are several causes leading to equipment adding failure:

①

Time-out error during adding camera on the App.

Solution: If the WiFi status indicator blinks red over one minute, please press
the reset button for 3-5 seconds untill the WiFi status indicator becomes
blinking blue, then confirm if the router signal is strong enough and input
correct router password to re-add the equipment.

②

On some Android phones, App prompts a message "Please input the default

password, 11111111"
Solution: The failure is caused by connection abnormal connection between
mobile phone and camera hot spot.
Please access to WiFi setup interface of your mobile phone to connect to the
camera hot point name is DOG-*** . Then enter the password:11111111)
manually and then return to app to add the camera.
If this does not work, please turn off the mobile phone WiFi and turn it back
on again. Repeat the above manual connection method to add the camera.

2 How to access the recorded video on micro SD card built-in inside
the camera?

The videos stored in the camera can be searched and playback using
“Doby” app installed on your mobile phone.

①

Accessories

②

Operation instruction
of the product

1.5.3 Setting: View device information and adjust settings

•

Device Name]: Rename your camera

•

[Location]: Select between Home or Office

•