SOLIS Palazzo Operating Instructions Download Page 3

To start programming mode, press both buttons
hold them down, and switch on machine again

1

2

3

1

2

PR

OGRAMMING

Switch off

Hardness 1

Hardness 2

Hardness 3*

Hardness 4

Measure
water hardness

Read after 1 min.

Press button

Machine wash
function

As soon as the machine
has been switched on,
the remaining water is
rinsed out. Therefore,
the very first cup of
coffee is made with
fresh water.

Press button

activated

not activated

Prebrewing function

The coffee is first
moistened and then
brewed after a short
pause!

activated

not activated

Press button

Pregrinding function

During preparation,
the next portion of coffee
will already be ground
(ideal if several coffees
need to be prepared at
same time)

activated

not activated

Press button

Switch off...

and switch on again to
activate the programmed functions

Start her

e

End her

e

and

Until appropriate setting...

*Basic setting

5

1 sec.

Fill water tank,
place receptacle under
outlet

Throw in cleaning
tablet

Press Clean for 5 sec.

1

2

3

1

2

3

Loosen the knurling
screw, remove nozzle

Clean with damp
cloth

Disassemble nozzle. Place
nozzle parts under running
water and remove milk residue.
Dry separate parts, reassemble,
and mount on machine.

Every 3-4 months or

if lamp

When button «Clean» goes out:
Cleaning is finished

1

2

-

To descale, make sure that the mains cable is plugged in and the

     machine switched on. During this process the heating is deactivated.

-

Use a non-poisonous, harmless, commercial decalcifying agent.

-

NEVER use VINEGAR 

(possible damage to device!)

-

Note manufacturer’s instructions!

-

If the machine is turned off during the descaling procedure, it will

     continue again where it left off when the machine is turned on again.

1

2

(automatic)

DESCALE

1. Place large receptacle under Cappuccino nozzle
2. Solipol rated 1:1 (0,5 l Solipol / 0,5 l Wasser)

in the water tank.

Preparation

Descale

Press buttons: Buttons «Clean»,
«Powder» and LED «Descale»
light

Open turning knob:
LED «Descale» flashes /
«Clean», «Powder» light

As soon as buttons / LED flash:
close turning knob

1

2

3

3

Rinse

1. Rinse water tank and fill
2. Open turning knob and draw off tank contents
3. Close turning knob, descaling is complete

6

Duration: approx. 45 min.

Duration: approx. 6 min.

Machine

CLEAN

Cappuccino nozzle

Summary of Contents for Palazzo






Reviews: