Temperature in °C or °F
3-digit room temperature display. Measurement Accuracy: +/– 1°C, measurement range 0°C + 50°C
2-digit room and outside humidity display. Measurement Accuracy: +/- 5%, measurement range 20% - 95%
3-digit outside temperature display. Measurement Accuracy: +/– 1°C, measurement range -20°C + 60°C
When an alarm goes off or when the device is in RCC signal reception mode (Radio Clock Control Signal), the device stops measuring temperature.
The high frequency receiver is capable of receiving data from up to three channels (transmitters)
Memory for storing maximum and minimum inside and outside temperature and humidity
Main unit and outdoor transmitter battery depletion indication on the display using the symbol
Units for air pressure measurement: mb/hPa, inHg
Alarm clock
Temperature alarm for outside temperature
5V USB output, supply power 1200 mA
Snooze function (5 minutes)
Daylight Saving Time (DST)
Moon phase indication
Environmental comfort function
Icing indication the symbol (for temperatures between –1°C and +3°C)
The device operates at a frequency of 433.92 MHz
3.
DEVICE FEATURES AND OPERATION
3.1
Setting Time
In standard mode, press the button for at least 2 seconds to get to the time setting mode. The active segment starts blinking.
Setting sequence: 12/24Hr → time zone shift → hours → minutes → date format DD/MM or MM/DD → year → MM/DD or DD/MM date setting (according to
the date format) → days of the week language (GE, FR, SP, IT, DU, DA, EN). Setting the values can be exited by pressing the button, resulting in the
segments stopping to blink. Pressing the or button brings you one step forward or backward; holding the buttons allows for quicker progression.
3.2
Setting the Alarm Clock
In standard mode, press the button, the time display section shows the set alarm time. In standard mode, press the button for at least 2 seconds to go
to the alarm clock setting mode, the main segment starts blinking. Setting sequence: hour → minute → exit. Pressing the or button brings you one
step forward or backward; holding the buttons allows for quicker progression. The snooze value is permanently set to 5 minutes. Setting the values can be
ended by moving through the menu, using the button, until the set segments stop blinking. Unless a button is pressed within 20 seconds, the device leaves
the setting mode and stores the currently set alarm time. If you want to turn off the alarm completely, move the alarm switch it to the off position.
3.3
Alarm Settings
Turning the alarm on or off is done using the on/off switch . When the alarm goes off, a ZZ symbol starts blinking on the display. If you press
/ ZZ when the alarm is sounding, the alarm will be postponed by 5 minutes. Pressing any other button turns the alarm off. Using the snooze function, an
alarm may be postponed indefinitely. When the alarm is sounding, the RCC signal is not being received. Reception resumes after the alarm is turned off. After
two minutes, the alarm is shut off automatically. The progression of the alarm sound is as follows: a) 0-10 seconds: one beep per second, b) 10 – 20 seconds two
beeps per second, c) after 20 seconds – three beeps per second.
3.4
Sensor Toggle Function
In standard mode, pressing the button will toggle channels (CH1, CH2, CH3 or the option of cycling through all three channels). When cycling is on, the
display shows the
symbol. In the cyclical three channel display mode the values change on their own. In the cyclical mode, when fewer than three outdoor
sensors are connected, the channels with no sensors connected will show no data.
3.5
Sensor Pairing Function
First, separate channels must be selected on the individual sensors. Open the battery compartment cover and move the position switch to the desired channel
number 1, 2, or 3. Reinsert the batteries and close the cover. When powering up for the first time, an automatic sensor pairing is conducted. If, however, you
want to change the pairing, change the channel by pressing the button and hold it for at least two seconds. The pairing process takes approximately three
minutes. If the pairing process is unsuccessful, the weather station is probably out of signal range.
3.6
Temperature Alarm Settings Functions
A temperature alarm can be set at the outdoor sensor side only.
To access the temperature alarm settings mode, hold the
button for at least 2 seconds.
First, the part of the display for setting the max. alarm temperature starts blinking. Using the or buttons, set the maximum temperature alarm value. By
briefly pressing the button, move on to setting the minimum alarm temperature. Using the or buttons set the minimum temperature alarm
value. Another brief pressing of the button will exit the temperature alarm settings mode. The range for the temperature alarm is from –20 °C to 60 °C.
The temperature alarm is activated by briefly pressing the button, what is indicated by the ALERTS notification being displayed:
When the minimum or maximum set temperature is exceeded, an alarm sounds, the value of the temperature exceeded starts blinking and a or
symbol is displayed. The alarm will sound for 5 seconds, unless it is shut off by pressing any button. If the sound alarm is terminated, but the temperature alarm
is not deactivated, the value of the temperature exceeding the preset range will keep blinking. The temperature alarm can be disabled by briefly pressing the
button. If the alarm is not disabled, it will be reactivated every minute, as long as the temperature stays outside of the preset range.
3.7
RCC Control Signal Reception
RCC signal reception is activated automatically upon powering up or resetting.
Forced RCC signal reception: press the button.
Once signal reception is activated, a three-minute synchronization period commences. While the synchronization is in progress, it is not possible to access
any functions and the weather station is not taking any measurements, The charging USB output is also deactivated.
Daily automatic signal reception.
