background image

Pág. 14

 

AUDIMAX 362 

SOLIDYNE

 

 

 

The Multiband control 

changes the input gain of 

the  compressors

.  This  control  affects  more 

radically  the  output  level  of  the  Audimax  362. 
Turning  this  knob  to  the  left  you  will  obtain  a 
smoother  sound,  with  little  processing  and 
therefore  with  less  energy.  Turning  it  to  the  right, 
you will increase the processing and the energy of 
the sound. 

Take  in  mind  that  with  an  excessive  processing 
you  will  obtain  a  very  hard  sound  on  the air, with 
high  energy,  but  too  compressed  (smaller 
dynamic  range)  and  with  less  definition  (more 
clipping). 

Normally  an  suitable  level  is  obtained  when  the 
indicators  LED’s  of  the  multiband  compressor act 
without light the red LED. 

 

Very  important:

  In  order  to  the  Dynamic  EQ  and 

Band  Energy  take  effect,  is  necessary  that  the 
multiband  compressor  works.  That  is  to  say,  in  all 
bands  the  first  LED  must  be  lights,  and  still  better, 
the second too. If the compressors don’t works, the 
others controls don’t take effect on the sound, since 
they are linked to the multiband compressor.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for AUDIMAX 362




















Reviews: