background image

PRODUCT MANUAL

 

Magro RGB-W Wireless LED Wall Controller / Wall Switch

Contact Us: 425.582.7533

www.SolidApollo.com 

[email protected] 

page 1

Manual Content

•   Product Information
•   Product Diagram & Parts
•   Product Wiring and Installation

Product Description

Solid Apollo’s Magro RGB-W Wireless Controller is a powerful low-profile controller 
that gives you full control of your RGB and RGBW LED fixtures either in your hand as 
a remote or by directly mounting it on any standard gang box.
Installation is basically effortless. You just have to screw the unit to any free gang box 
and it’s ready to work. Thanks to its included 3V DC durable battery, there is no messy 
cable connections. 
The Magro Wireless Controller Switch lets you use it in two different exciting ways: as 
a hand-held remote or as a wall controller/switch. The unit is magnetically attached 
to the faceplate which makes it easy to detach and carry as a hand-held remote or 
dock and use as an in-wall controller.

Product Features

•   1 x Magro Wireless Wall Controller
•   1 x White Wall-Plate
•   4 x 5A Receiver
•   Perfectly installs in any standard gang box
•   Controls RGB and RGBW LED fixtures
•   Separate W and RGB control buttons
•   Can be docked or used as hand-held remote
•   Full dimming from 100% - 1%
•   Impressive 65ft wireless range
•   Battery operated (3V DC - CR2025)
•   Soft ramping ON/OFF technology
•   Easy installation and operation
•   Easy installation and operation
•   Memory function - Remember last 

  setting before losing power.

 

Product Specs

Magro RGB-WController

•   Dimming :
•   Input Voltage :
•   Battery Type :
•   Weight :
•   Control System :
•   Frequency : 
•   Range : 
•   Dimension :

100% to 1%
3V DC Battery
CR2025 (included)
0.12 lb
Radio Frequency
916.5 MHz
65ft
2.6” x 1.2” x 0.37”

Receiver

•   Input Voltage :
•   Max Power : 

•   Max Amps :
•   Dimensions :
•   Weight :
•   IP Rating : 
•   Working Temp : 
•   Warranty :
•   Certificates :

12V - 36V DC
240W@12V DC 

720W@36V DC
4x 5A
7” x 1.8” x 0.87”
0.30 lb
IP20
- 30F - 160F
3 Years
CE, RoHs, UL listed

•   Product Operation
•   Product Troubleshooting

Summary of Contents for Magro







Reviews: